/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00BN5A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 9 00:08:45 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 115) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 175 168 021 - 2250 4 Start_Stop_Count -O--CK 098 098 000 - 2295 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 076 076 000 - 17797 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2224 192 Power-Off_Retract_Count -O--CK 200 200 000 - 61 193 Load_Cycle_Count -O--CK 200 200 000 - 2235 194 Temperature_Celsius -O---K 113 095 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 114 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 114 [17] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.204 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.204 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.203 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:42.203 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.203 IDENTIFY DEVICE Error 113 [16] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.204 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.203 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:42.203 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.203 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.202 IDENTIFY DEVICE Error 112 [15] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:42.203 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:42.203 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.203 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.202 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:42.202 IDENTIFY DEVICE Error 111 [14] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.846 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.846 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.845 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:15.845 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.845 IDENTIFY DEVICE Error 110 [13] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.846 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.845 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:15.845 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.845 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.844 IDENTIFY DEVICE Error 109 [12] occurred at disk power-on lifetime: 12036 hours (501 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 07:39:15.845 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 07:39:15.845 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.845 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.844 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 07:39:15.844 IDENTIFY DEVICE Error 108 [11] occurred at disk power-on lifetime: 11880 hours (495 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 03:01:39.050 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 03:01:39.050 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 03:01:39.049 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:01:39.049 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 03:01:39.049 IDENTIFY DEVICE Error 107 [10] occurred at disk power-on lifetime: 11880 hours (495 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 03:01:39.050 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 03:01:39.049 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 03:01:39.049 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 03:01:39.049 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 03:01:39.048 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 19/31 Celsius Lifetime Min/Max Temperature: 8/48 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (203) Index Estimated Time Temperature Celsius 204 2024-01-08 16:11 30 *********** ... ..( 12 skipped). .. *********** 217 2024-01-08 16:24 30 *********** 218 2024-01-08 16:25 31 ************ ... ..( 62 skipped). .. ************ 281 2024-01-08 17:28 31 ************ 282 2024-01-08 17:29 30 *********** ... ..(398 skipped). .. *********** 203 2024-01-09 00:08 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 54322 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Samsung SSD 870 EVO 1TB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT02B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 9 00:08:45 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 098 098 000 - 5354 12 Power_Cycle_Count -O--CK 099 099 000 - 505 177 Wear_Leveling_Count PO--C- 099 099 000 - 22 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 050 000 - 30 195 Hardware_ECC_Recovered -O-RC- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 235 Unknown_Attribute -O--C- 099 099 000 - 22 241 Total_LBAs_Written -O--CK 099 099 000 - 54820823562 252 Unknown_Attribute -O--CK 100 100 000 - 7 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 25/40 Celsius Lifetime Min/Max Temperature: 17/50 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (25) Index Estimated Time Temperature Celsius 26 2024-01-08 02:50 29 ********** ... ..( 2 skipped). .. ********** 29 2024-01-08 03:20 29 ********** 30 2024-01-08 03:30 30 *********** 31 2024-01-08 03:40 30 *********** 32 2024-01-08 03:50 28 ********* 33 2024-01-08 04:00 27 ******** 34 2024-01-08 04:10 27 ******** 35 2024-01-08 04:20 26 ******* ... ..( 4 skipped). .. ******* 40 2024-01-08 05:10 26 ******* 41 2024-01-08 05:20 31 ************ 42 2024-01-08 05:30 27 ******** 43 2024-01-08 05:40 29 ********** ... ..( 3 skipped). .. ********** 47 2024-01-08 06:20 29 ********** 48 2024-01-08 06:30 30 *********** 49 2024-01-08 06:40 34 *************** 50 2024-01-08 06:50 30 *********** 51 2024-01-08 07:00 29 ********** 52 2024-01-08 07:10 28 ********* 53 2024-01-08 07:20 29 ********** 54 2024-01-08 07:30 28 ********* 55 2024-01-08 07:40 31 ************ 56 2024-01-08 07:50 27 ******** 57 2024-01-08 08:00 26 ******* ... ..( 2 skipped). .. ******* 60 2024-01-08 08:30 26 ******* 61 2024-01-08 08:40 28 ********* 62 2024-01-08 08:50 26 ******* 63 2024-01-08 09:00 ? - 64 2024-01-08 09:10 27 ******** 65 2024-01-08 09:20 27 ******** 66 2024-01-08 09:30 30 *********** 67 2024-01-08 09:40 31 ************ 68 2024-01-08 09:50 27 ******** 69 2024-01-08 10:00 28 ********* 70 2024-01-08 10:10 28 ********* 71 2024-01-08 10:20 29 ********** 72 2024-01-08 10:30 27 ******** 73 2024-01-08 10:40 27 ******** 74 2024-01-08 10:50 28 ********* 75 2024-01-08 11:00 27 ******** 76 2024-01-08 11:10 28 ********* ... ..( 4 skipped). .. ********* 81 2024-01-08 12:00 28 ********* 82 2024-01-08 12:10 29 ********** 83 2024-01-08 12:20 28 ********* 84 2024-01-08 12:30 28 ********* 85 2024-01-08 12:40 27 ******** 86 2024-01-08 12:50 28 ********* 87 2024-01-08 13:00 28 ********* 88 2024-01-08 13:10 27 ******** 89 2024-01-08 13:20 26 ******* ... ..( 2 skipped). .. ******* 92 2024-01-08 13:50 26 ******* 93 2024-01-08 14:00 25 ****** 94 2024-01-08 14:10 26 ******* 95 2024-01-08 14:20 26 ******* 96 2024-01-08 14:30 27 ******** 97 2024-01-08 14:40 27 ******** 98 2024-01-08 14:50 28 ********* 99 2024-01-08 15:00 29 ********** 100 2024-01-08 15:10 28 ********* 101 2024-01-08 15:20 28 ********* 102 2024-01-08 15:30 28 ********* 103 2024-01-08 15:40 27 ******** ... ..( 6 skipped). .. ******** 110 2024-01-08 16:50 27 ******** 111 2024-01-08 17:00 28 ********* ... ..( 2 skipped). .. ********* 114 2024-01-08 17:30 28 ********* 115 2024-01-08 17:40 33 ************** 116 2024-01-08 17:50 29 ********** 117 2024-01-08 18:00 28 ********* 118 2024-01-08 18:10 29 ********** 119 2024-01-08 18:20 28 ********* 120 2024-01-08 18:30 28 ********* 121 2024-01-08 18:40 35 **************** 122 2024-01-08 18:50 36 ***************** 123 2024-01-08 19:00 38 ******************* 124 2024-01-08 19:10 27 ******** ... ..( 4 skipped). .. ******** 1 2024-01-08 20:00 27 ******** 2 2024-01-08 20:10 26 ******* 3 2024-01-08 20:20 29 ********** 4 2024-01-08 20:30 27 ******** 5 2024-01-08 20:40 28 ********* 6 2024-01-08 20:50 27 ******** 7 2024-01-08 21:00 27 ******** 8 2024-01-08 21:10 27 ******** 9 2024-01-08 21:20 28 ********* 10 2024-01-08 21:30 28 ********* 11 2024-01-08 21:40 28 ********* 12 2024-01-08 21:50 29 ********** 13 2024-01-08 22:00 29 ********** 14 2024-01-08 22:10 30 *********** 15 2024-01-08 22:20 28 ********* ... ..( 8 skipped). .. ********* 24 2024-01-08 23:50 28 ********* 25 2024-01-09 00:00 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 505 --- Lifetime Power-On Resets 0x01 0x010 4 5354 --- Power-on Hours 0x01 0x018 6 54820823562 --- Logical Sectors Written 0x01 0x020 6 292056109 --- Number of Write Commands 0x01 0x028 6 61194653628 --- Logical Sectors Read 0x01 0x030 6 310988859 --- Number of Read Commands 0x01 0x038 6 291000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 30 --- Current Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1115 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC46 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Jan 9 00:08:45 2024 CET ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 83) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 111 099 006 - 31032273 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 084 084 020 - 16958 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 861280670 9 Power_On_Hours -O--CK 072 072 000 - 25321 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4478 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 096 000 - 94490723272 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 077 047 045 - 23 (Min/Max 18/30) 194 Temperature_Celsius -O---K 023 053 000 - 23 (0 7 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 024 011 000 - 31032273 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 2 240 Head_Flying_Hours ------ 100 253 000 - 41882 (79 214 0) 241 Total_LBAs_Written ------ 100 253 000 - 1384645591 242 Total_LBAs_Read ------ 100 253 000 - 2301468768 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 25270 - # 2 Short offline Completed without error 00% 24676 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 18/30 Celsius Lifetime Min/Max Temperature: 7/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (6) Index Estimated Time Temperature Celsius 7 2024-01-03 18:58 19 - 8 2024-01-03 19:57 20 * 9 2024-01-03 20:56 ? - 10 2024-01-03 21:55 20 * 11 2024-01-03 22:54 ? - 12 2024-01-03 23:53 17 - 13 2024-01-04 00:52 ? - 14 2024-01-04 01:51 18 - 15 2024-01-04 02:50 ? - 16 2024-01-04 03:49 19 - 17 2024-01-04 04:48 ? - 18 2024-01-04 05:47 19 - 19 2024-01-04 06:46 ? - 20 2024-01-04 07:45 17 - 21 2024-01-04 08:44 17 - 22 2024-01-04 09:43 ? - 23 2024-01-04 10:42 18 - 24 2024-01-04 11:41 ? - 25 2024-01-04 12:40 18 - 26 2024-01-04 13:39 ? - 27 2024-01-04 14:38 18 - 28 2024-01-04 15:37 ? - 29 2024-01-04 16:36 18 - 30 2024-01-04 17:35 ? - 31 2024-01-04 18:34 19 - 32 2024-01-04 19:33 ? - 33 2024-01-04 20:32 20 * 34 2024-01-04 21:31 ? - 35 2024-01-04 22:30 18 - 36 2024-01-04 23:29 ? - 37 2024-01-05 00:28 19 - 38 2024-01-05 01:27 ? - 39 2024-01-05 02:26 17 - 40 2024-01-05 03:25 ? - 41 2024-01-05 04:24 19 - 42 2024-01-05 05:23 ? - 43 2024-01-05 06:22 19 - 44 2024-01-05 07:21 ? - 45 2024-01-05 08:20 19 - 46 2024-01-05 09:19 ? - 47 2024-01-05 10:18 17 - 48 2024-01-05 11:17 ? - 49 2024-01-05 12:16 15 - 50 2024-01-05 13:15 ? - 51 2024-01-05 14:14 15 - 52 2024-01-05 15:13 ? - 53 2024-01-05 16:12 15 - 54 2024-01-05 17:11 15 - 55 2024-01-05 18:10 21 ** 56 2024-01-05 19:09 ? - 57 2024-01-05 20:08 15 - 58 2024-01-05 21:07 ? - 59 2024-01-05 22:06 17 - 60 2024-01-05 23:05 ? - 61 2024-01-06 00:04 15 - 62 2024-01-06 01:03 ? - 63 2024-01-06 02:02 15 - 64 2024-01-06 03:01 ? - 65 2024-01-06 04:00 16 - 66 2024-01-06 04:59 ? - 67 2024-01-06 05:58 15 - 68 2024-01-06 06:57 15 - 69 2024-01-06 07:56 ? - 70 2024-01-06 08:55 15 - 71 2024-01-06 09:54 15 - 72 2024-01-06 10:53 ? - 73 2024-01-06 11:52 16 - 74 2024-01-06 12:51 16 - 75 2024-01-06 13:50 ? - 76 2024-01-06 14:49 16 - 77 2024-01-06 15:48 ? - 78 2024-01-06 16:47 17 - 79 2024-01-06 17:46 ? - 80 2024-01-06 18:45 18 - 81 2024-01-06 19:44 18 - 82 2024-01-06 20:43 ? - 83 2024-01-06 21:42 18 - 84 2024-01-06 22:41 ? - 85 2024-01-06 23:40 17 - 86 2024-01-07 00:39 17 - 87 2024-01-07 01:38 ? - 88 2024-01-07 02:37 14 - 89 2024-01-07 03:36 ? - 90 2024-01-07 04:35 15 - 91 2024-01-07 05:34 ? - 92 2024-01-07 06:33 15 - 93 2024-01-07 07:32 ? - 94 2024-01-07 08:31 14 - 95 2024-01-07 09:30 ? - 96 2024-01-07 10:29 15 - 97 2024-01-07 11:28 ? - 98 2024-01-07 12:27 12 - 99 2024-01-07 13:26 ? - 100 2024-01-07 14:25 14 - 101 2024-01-07 15:24 15 - 102 2024-01-07 16:23 ? - 103 2024-01-07 17:22 15 - 104 2024-01-07 18:21 ? - 105 2024-01-07 19:20 16 - 106 2024-01-07 20:19 ? - 107 2024-01-07 21:18 17 - 108 2024-01-07 22:17 ? - 109 2024-01-07 23:16 24 ***** 110 2024-01-08 00:15 ? - 111 2024-01-08 01:14 17 - 112 2024-01-08 02:13 ? - 113 2024-01-08 03:12 17 - 114 2024-01-08 04:11 17 - 115 2024-01-08 05:10 ? - 116 2024-01-08 06:09 17 - 117 2024-01-08 07:08 ? - 118 2024-01-08 08:07 17 - 119 2024-01-08 09:06 ? - 120 2024-01-08 10:05 18 - 121 2024-01-08 11:04 ? - 122 2024-01-08 12:03 18 - 123 2024-01-08 13:02 ? - 124 2024-01-08 14:01 18 - 125 2024-01-08 15:00 18 - 126 2024-01-08 15:59 ? - 127 2024-01-08 16:58 18 - 0 2024-01-08 17:57 18 - 1 2024-01-08 18:56 28 ********* 2 2024-01-08 19:55 ? - 3 2024-01-08 20:54 18 - 4 2024-01-08 21:53 18 - 5 2024-01-08 22:52 23 **** 6 2024-01-08 23:51 23 **** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD20NMVW-11AV3S0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5200 rpm Device is: In smartctl database ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jan 9 00:08:45 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (35220) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 389) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 228 220 021 - 3575 4 Start_Stop_Count -O--CK 091 091 000 - 9049 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 061 061 000 - 28775 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2630 192 Power-Off_Retract_Count -O--CK 200 200 000 - 318 193 Load_Cycle_Count -O--CK 086 086 000 - 342507 194 Temperature_Celsius -O---K 121 099 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2531 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2531 [10] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 e2 20 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6e220 = 64414240 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 e2 20 40 00 01:05:51.800 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e1 a0 40 00 01:05:51.796 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e1 20 40 00 01:05:51.793 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 a0 40 00 01:05:51.790 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 20 40 00 01:05:51.787 WRITE DMA EXT Error 2530 [9] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 e1 a0 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6e1a0 = 64414112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 e1 a0 40 00 01:05:51.796 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e1 20 40 00 01:05:51.793 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 a0 40 00 01:05:51.790 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 20 40 00 01:05:51.787 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df a0 40 00 01:05:51.785 WRITE DMA EXT Error 2529 [8] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 e1 20 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6e120 = 64413984 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 e1 20 40 00 01:05:51.793 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 a0 40 00 01:05:51.790 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 20 40 00 01:05:51.787 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df a0 40 00 01:05:51.785 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df 20 40 00 01:05:51.782 WRITE DMA EXT Error 2528 [7] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 e0 a0 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6e0a0 = 64413856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 e0 a0 40 00 01:05:51.790 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 e0 20 40 00 01:05:51.787 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df a0 40 00 01:05:51.785 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df 20 40 00 01:05:51.782 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de a0 40 00 01:05:51.779 WRITE DMA EXT Error 2527 [6] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 e0 20 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6e020 = 64413728 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 e0 20 40 00 01:05:51.787 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df a0 40 00 01:05:51.785 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df 20 40 00 01:05:51.782 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de a0 40 00 01:05:51.779 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de 20 40 00 01:05:51.776 WRITE DMA EXT Error 2526 [5] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 df a0 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6dfa0 = 64413600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 df a0 40 00 01:05:51.785 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 df 20 40 00 01:05:51.782 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de a0 40 00 01:05:51.779 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de 20 40 00 01:05:51.776 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dd a0 40 00 01:05:51.774 WRITE DMA EXT Error 2525 [4] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 df 20 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6df20 = 64413472 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 df 20 40 00 01:05:51.782 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de a0 40 00 01:05:51.779 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de 20 40 00 01:05:51.776 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dd a0 40 00 01:05:51.774 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dd 20 40 00 01:05:51.771 WRITE DMA EXT Error 2524 [3] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 80 00 00 03 d6 de a0 40 00 Device Fault; Error: ABRT 128 sectors at LBA = 0x03d6dea0 = 64413344 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 03 d6 de a0 40 00 01:05:51.779 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 de 20 40 00 01:05:51.776 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dd a0 40 00 01:05:51.774 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dd 20 40 00 01:05:51.771 WRITE DMA EXT 35 00 00 00 80 00 00 03 d6 dc a0 40 00 01:05:51.768 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 28013 - # 2 Short offline Completed without error 00% 15935 - # 3 Short offline Completed without error 00% 11841 - # 4 Short offline Completed without error 00% 9931 - # 5 Short offline Completed without error 00% 5937 - # 6 Short offline Completed without error 00% 4441 - # 7 Short offline Completed without error 00% 4185 - # 8 Short offline Completed without error 00% 3264 - # 9 Short offline Completed without error 00% 735 - #10 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 14/37 Celsius Lifetime Min/Max Temperature: 12/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (40) Index Estimated Time Temperature Celsius 41 2024-01-08 22:01 31 ************ ... ..( 24 skipped). .. ************ 66 2024-01-08 22:26 31 ************ 67 2024-01-08 22:27 32 ************* 68 2024-01-08 22:28 31 ************ 69 2024-01-08 22:29 31 ************ 70 2024-01-08 22:30 32 ************* ... ..( 23 skipped). .. ************* 94 2024-01-08 22:54 32 ************* 95 2024-01-08 22:55 33 ************** 96 2024-01-08 22:56 32 ************* ... ..( 2 skipped). .. ************* 99 2024-01-08 22:59 32 ************* 100 2024-01-08 23:00 33 ************** 101 2024-01-08 23:01 32 ************* ... ..( 16 skipped). .. ************* 118 2024-01-08 23:18 32 ************* 119 2024-01-08 23:19 33 ************** 120 2024-01-08 23:20 33 ************** 121 2024-01-08 23:21 32 ************* 122 2024-01-08 23:22 32 ************* 123 2024-01-08 23:23 32 ************* 124 2024-01-08 23:24 33 ************** 125 2024-01-08 23:25 33 ************** 126 2024-01-08 23:26 32 ************* ... ..( 14 skipped). .. ************* 13 2024-01-08 23:41 32 ************* 14 2024-01-08 23:42 31 ************ ... ..( 25 skipped). .. ************ 40 2024-01-09 00:08 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 40 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 27 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1133060 Vendor specific /dev/sde smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD50NMZW-59A8NS1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 5,000,947,523,584 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 9 00:08:45 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14940) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 629) minutes. SCT capabilities: (0x30b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 196 193 051 - 278 3 Spin_Up_Time POS--K 253 253 021 - 2550 4 Start_Stop_Count -O--CK 096 096 000 - 4207 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11231 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 431 192 Power-Off_Retract_Count -O--CK 200 200 000 - 40 193 Load_Cycle_Count -O--CK 184 184 000 - 48846 194 Temperature_Celsius -O---K 114 090 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 77 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 289 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 82 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xcf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 145 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 145 [0] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 06 00 00 01 74 9d d5 18 40 00 Error: UNC 1536 sectors at LBA = 0x1749dd518 = 6251468056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 04 00 00 01 74 9d d1 28 40 00 04:59:27.284 READ DMA EXT 25 00 d5 06 00 00 01 74 9d cb 28 40 00 04:59:27.244 READ DMA EXT 25 00 d5 03 00 00 01 74 9d c8 28 40 00 04:59:27.239 READ DMA EXT 25 00 d5 04 00 00 01 74 9d c4 28 40 00 04:59:27.234 READ DMA EXT 25 00 d5 02 00 00 01 74 9d c2 28 40 00 04:59:27.231 READ DMA EXT Error 144 [23] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 04 00 00 01 74 9b de 18 40 00 Error: UNC 1024 sectors at LBA = 0x1749bde18 = 6251339288 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 07 20 00 01 74 9b d8 30 40 00 04:58:40.963 READ DMA EXT 25 00 d5 04 00 00 01 74 9b d4 30 40 00 04:58:40.846 READ DMA EXT 25 00 d5 04 e0 00 01 74 9b cf 50 40 00 04:58:40.840 READ DMA EXT 25 00 d5 02 70 00 01 74 9b cc e0 40 00 04:58:40.835 READ DMA EXT 25 00 d5 04 00 00 01 74 9b c8 e0 40 00 04:58:40.830 READ DMA EXT Error 143 [22] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 03 00 00 01 74 9b 3a 50 40 00 Error: UNC 768 sectors at LBA = 0x1749b3a50 = 6251297360 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 06 00 00 01 74 9b 34 c8 40 00 04:58:05.398 READ DMA EXT 25 00 d5 03 00 00 01 74 9b 31 c8 40 00 04:58:05.294 READ DMA EXT 25 00 d5 04 00 00 01 74 9b 2d c8 40 00 04:58:05.289 READ DMA EXT 25 00 d5 02 00 00 01 74 9b 2b c8 40 00 04:58:05.286 READ DMA EXT 25 00 d5 01 00 00 01 74 9b 2a c8 40 00 04:58:05.285 READ DMA EXT Error 142 [21] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 01 74 88 c6 60 40 00 Error: UNC 8 sectors at LBA = 0x17488c660 = 6250088032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 08 00 01 74 88 c6 60 40 00 04:57:43.427 READ DMA EXT 25 00 d5 00 08 00 01 74 88 c6 58 40 00 04:57:43.427 READ DMA EXT 25 00 d5 00 08 00 01 74 88 c6 50 40 00 04:57:43.427 READ DMA EXT 25 00 d5 00 08 00 01 74 88 c6 48 40 00 04:57:43.427 READ DMA EXT 25 00 d5 00 08 00 01 74 88 c6 40 40 00 04:57:43.427 READ DMA EXT Error 141 [20] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 01 74 88 c6 60 40 00 Error: UNC 2048 sectors at LBA = 0x17488c660 = 6250088032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 08 00 00 01 74 88 c0 00 40 00 04:57:12.061 READ DMA EXT 25 00 d5 08 00 00 01 74 88 b8 00 40 00 04:57:09.908 READ DMA EXT 25 00 d5 08 00 00 01 74 88 b0 00 40 00 04:57:09.797 READ DMA EXT 25 00 d5 08 00 00 01 74 88 a8 00 40 00 04:57:09.775 READ DMA EXT 25 00 d5 08 00 00 01 74 88 a0 00 40 00 04:57:09.709 READ DMA EXT Error 140 [19] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 01 74 36 26 80 40 00 Error: UNC 2048 sectors at LBA = 0x174362680 = 6244673152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 08 00 00 01 74 36 20 00 40 00 04:56:07.257 READ DMA EXT 25 00 d5 08 00 00 01 74 36 18 00 40 00 04:56:06.471 READ DMA EXT 25 00 d5 08 00 00 01 74 36 10 00 40 00 04:56:06.193 READ DMA EXT 25 00 d5 08 00 00 01 74 36 08 00 40 00 04:56:05.849 READ DMA EXT 25 00 d5 08 00 00 01 74 36 00 00 40 00 04:56:05.822 READ DMA EXT Error 139 [18] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 01 74 35 f5 28 40 00 Error: UNC 2048 sectors at LBA = 0x17435f528 = 6244660520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 08 00 00 01 74 35 f0 00 40 00 04:55:34.125 READ DMA EXT 25 00 d5 08 00 00 01 74 35 e8 00 40 00 04:55:31.484 READ DMA EXT 25 00 d5 08 00 00 01 74 35 e0 00 40 00 04:55:30.364 READ DMA EXT 25 00 d5 00 08 00 01 74 35 d7 f8 40 00 04:55:30.364 READ DMA EXT 25 00 d5 00 08 00 01 74 35 d7 f0 40 00 04:55:30.363 READ DMA EXT Error 138 [17] occurred at disk power-on lifetime: 10046 hours (418 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 01 74 35 d4 b8 40 00 Error: UNC 2048 sectors at LBA = 0x17435d4b8 = 6244652216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 08 00 00 01 74 35 d0 00 40 00 04:54:56.387 READ DMA EXT 25 00 d5 08 00 00 01 74 35 c8 00 40 00 04:54:52.091 READ DMA EXT 25 00 d5 08 00 00 01 74 35 c0 00 40 00 04:54:51.736 READ DMA EXT 25 00 d5 08 00 00 01 74 35 b8 00 40 00 04:54:48.961 READ DMA EXT 25 00 d5 08 00 00 01 74 35 b0 00 40 00 04:54:48.841 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 10469 - Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 20/43 Celsius Lifetime Min/Max Temperature: 15/63 Celsius Specified Max Operating Temperature: 44 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (119) Index Estimated Time Temperature Celsius 120 2024-01-08 22:01 38 ******************* ... ..( 26 skipped). .. ******************* 19 2024-01-08 22:28 38 ******************* 20 2024-01-08 22:29 ? - 21 2024-01-08 22:30 38 ******************* ... ..( 59 skipped). .. ******************* 81 2024-01-08 23:30 38 ******************* 82 2024-01-08 23:31 ? - 83 2024-01-08 23:32 38 ******************* ... ..( 35 skipped). .. ******************* 119 2024-01-09 00:08 38 ******************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1133008 Vendor specific /dev/sdf smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7 Device Model: SAMSUNG HM500JI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AC101C4 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Form Factor: 2.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Jan 9 00:08:45 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 8820) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 147) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 6039 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 090 086 025 - 3310 4 Start_Stop_Count -O--CK 088 088 000 - 12638 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 30922 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 92 12 Power_Cycle_Count -O--CK 096 096 000 - 4658 191 G-Sense_Error_Rate -O---K 100 100 000 - 63 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 051 000 - 35 (Min/Max 11/57) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 8 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2036 223 Load_Retry_Count -O--CK 100 100 000 - 92 225 Load_Cycle_Count -O--CK 001 001 000 - 2021320 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 4942 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4942 [5] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.109 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 4b 40 00 00:00:50.109 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 bf 40 00 00:00:50.109 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.106 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 49 40 00 00:00:50.106 READ DMA EXT Error 4941 [4] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.106 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 49 40 00 00:00:50.106 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 bf 40 00 00:00:50.106 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.103 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 41 40 00 00:00:50.103 READ DMA EXT Error 4940 [3] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.103 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 41 40 00 00:00:50.103 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 bf 40 00 00:00:50.103 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.100 READ DMA EXT 25 52 d5 00 04 00 00 07 2e 53 49 40 00 00:00:50.099 READ DMA EXT Error 4939 [2] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.100 READ DMA EXT 25 52 d5 00 04 00 00 07 2e 53 49 40 00 00:00:50.099 READ DMA EXT 35 52 d5 00 04 00 00 07 2e 53 49 40 00 00:00:50.099 WRITE DMA EXT 25 52 d5 00 08 00 00 2a 80 2e 4f 40 00 00:00:50.099 READ DMA EXT 35 52 d5 00 08 00 00 2a 80 2e 4f 40 00 00:00:50.099 WRITE DMA EXT Error 4938 [1] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.083 READ DMA EXT 25 52 d5 00 80 00 00 00 4a 2b bf 40 00 00:00:50.083 READ DMA EXT 25 52 d5 00 80 00 00 00 4a 2b 3f 40 00 00:00:50.083 READ DMA EXT 25 52 d5 00 80 00 00 00 0e fe bf 40 00 00:00:50.083 READ DMA EXT 25 52 d5 00 80 00 00 00 0e fe 3f 40 00 00:00:50.083 READ DMA EXT Error 4937 [0] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.069 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 4d 40 00 00:00:50.069 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 bf 40 00 00:00:50.069 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.066 READ DMA EXT 25 52 d5 00 80 00 00 09 3c 30 bf 40 00 00:00:50.066 READ DMA EXT Error 4936 [7] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.066 READ DMA EXT 25 52 d5 00 80 00 00 09 3c 30 bf 40 00 00:00:50.066 READ DMA EXT 25 52 d5 00 80 00 00 09 3c 30 3f 40 00 00:00:50.066 READ DMA EXT 25 52 d5 00 80 00 00 09 3c 31 bf 40 00 00:00:50.066 READ DMA EXT 25 52 d5 00 80 00 00 09 3c 31 3f 40 00 00:00:50.066 READ DMA EXT Error 4935 [6] occurred at disk power-on lifetime: 30131 hours (1255 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 00 61 d2 4f 40 00 Error: UNC 112 sectors at LBA = 0x0061d24f = 6410831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.061 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 4b 40 00 00:00:50.061 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 bf 40 00 00:00:50.061 READ DMA EXT 25 52 d5 00 80 00 00 00 61 d2 3f 40 00 00:00:50.058 READ DMA EXT 25 52 d5 00 02 00 00 00 61 d2 49 40 00 00:00:50.058 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 90% 30551 6410831 # 2 Extended offline Completed: read failure 90% 4897 6410831 # 3 Short offline Completed: read failure 90% 4325 6410831 # 4 Short offline Completed: read failure 90% 4325 6410831 # 5 Vendor (0xd2) Completed without error 00% 97 - # 6 Offline Completed without error 00% 54528 - # 7 Offline Fatal or unknown error 120% 16384 12816896 # 8 Offline Unknown status (0xd) 50% 32850 - # 9 Short offline Unknown status (0x9) 120% 65535 - #10 Offline Completed: unknown failure 00% 112 70370371621376 #11 Offline Completed: unknown failure 00% 37 91074781511875 #12 Vendor (0x52) Completed: handling damage?? 00% 48896 40956814491858 #13 Reserved (0x25) Completed without error 00% 50058 - #14 Reserved (0x06) Completed: electrical failure 20% 49932 281474970157314 #15 Reserved (0x25) Completed without error 00% 50109 - #16 Offline Completed: unknown failure 110% 53760 207808322601057 #17 Vendor (0xba) Unknown status (0xc) 30% 0 - #18 Offline Unknown status (0xd) 20% 24832 - #19 Vendor (0x53) Completed: unknown failure 50% 8560 837725324806 #20 Offline Unknown status (0xd) 20% 24832 - #21 Offline Completed without error 00% 54528 - #22 Offline Completed without error 00% 0 - #23 Offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_read_failure [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 17/39 Celsius Lifetime Min/Max Temperature: 13/57 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (126) Index Estimated Time Temperature Celsius 127 2024-01-08 13:30 34 *************** 0 2024-01-08 13:35 34 *************** 1 2024-01-08 13:40 34 *************** 2 2024-01-08 13:45 33 ************** ... ..( 12 skipped). .. ************** 15 2024-01-08 14:50 33 ************** 16 2024-01-08 14:55 34 *************** ... ..( 2 skipped). .. *************** 19 2024-01-08 15:10 34 *************** 20 2024-01-08 15:15 35 **************** ... ..( 8 skipped). .. **************** 29 2024-01-08 16:00 35 **************** 30 2024-01-08 16:05 34 *************** ... ..( 3 skipped). .. *************** 34 2024-01-08 16:25 34 *************** 35 2024-01-08 16:30 33 ************** ... ..( 2 skipped). .. ************** 38 2024-01-08 16:45 33 ************** 39 2024-01-08 16:50 34 *************** ... ..( 24 skipped). .. *************** 64 2024-01-08 18:55 34 *************** 65 2024-01-08 19:00 35 **************** 66 2024-01-08 19:05 35 **************** 67 2024-01-08 19:10 36 ***************** 68 2024-01-08 19:15 35 **************** 69 2024-01-08 19:20 34 *************** ... ..( 2 skipped). .. *************** 72 2024-01-08 19:35 34 *************** 73 2024-01-08 19:40 33 ************** ... ..( 3 skipped). .. ************** 77 2024-01-08 20:00 33 ************** 78 2024-01-08 20:05 34 *************** ... ..( 19 skipped). .. *************** 98 2024-01-08 21:45 34 *************** 99 2024-01-08 21:50 35 **************** ... ..( 2 skipped). .. **************** 102 2024-01-08 22:05 35 **************** 103 2024-01-08 22:10 34 *************** 104 2024-01-08 22:15 35 **************** 105 2024-01-08 22:20 36 ***************** 106 2024-01-08 22:25 36 ***************** 107 2024-01-08 22:30 37 ****************** 108 2024-01-08 22:35 37 ****************** 109 2024-01-08 22:40 37 ****************** 110 2024-01-08 22:45 38 ******************* ... ..( 7 skipped). .. ******************* 118 2024-01-08 23:25 38 ******************* 119 2024-01-08 23:30 37 ****************** 120 2024-01-08 23:35 36 ***************** 121 2024-01-08 23:40 36 ***************** 122 2024-01-08 23:45 35 **************** ... ..( 3 skipped). .. **************** 126 2024-01-09 00:05 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific