/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.18-generic-1rosa2019.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Palit UVS 120GB Serial Number: -- Firmware Version: SBFM61.3 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Mar 6 13:27:48 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 2598 12 Power_Cycle_Count -O--C- 100 100 000 - 1498 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 094 094 000 - 56 173 Unknown_Attribute -O--C- 100 100 000 - 1441821 192 Power-Off_Retract_Count -O--C- 100 100 000 - 328 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 Unknown_Attribute PO-R-- 100 100 050 - 0 231 Unknown_SSD_Attribute PO--C- 100 100 000 - 99 241 Total_LBAs_Written -O--C- 100 100 000 - 2622 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1498 --- Lifetime Power-On Resets 0x01 0x010 4 2598 --- Power-on Hours 0x01 0x018 6 5499516385 --- Logical Sectors Written 0x01 0x028 6 5608321094 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.18-generic-1rosa2019.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST380815AS Serial Number: -- Firmware Version: 4.AAB User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Mar 6 13:27:48 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9982 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 088 060 030 - 778072987 9 Power_On_Hours -O--CK 080 080 000 - 17974 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 086 086 020 - 14379 187 Reported_Uncorrect -O--CK 048 048 000 - 52 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 056 049 045 - 44 (Min/Max 27/44) 194 Temperature_Celsius -O---K 044 051 000 - 44 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 069 062 000 - 80352590 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 198 000 - 102 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 58 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 58 [17] occurred at disk power-on lifetime: 5051 hours (210 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 20 00 01 1c 00 42 ff e1 00 00:34:31.069 READ DMA ca 00 00 00 08 00 00 45 00 fc 77 e0 00 00:34:31.068 WRITE DMA ca 00 00 00 0a 00 02 4b 00 b5 47 e2 00 00:34:31.068 WRITE DMA ca 00 00 00 08 00 00 da 00 04 9f e0 00 00:34:31.063 WRITE DMA ca 00 00 00 10 00 00 09 00 0b 0f e0 00 00:34:31.063 WRITE DMA Error 57 [16] occurred at disk power-on lifetime: 5047 hours (210 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 01:39:01.011 READ DMA Error 56 [15] occurred at disk power-on lifetime: 5079 hours (211 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 01 1c 00 42 df e1 00 01:35:11.583 READ DMA c8 00 00 00 08 00 00 32 00 ae b7 e0 00 01:35:11.581 READ DMA c8 00 00 00 48 00 03 37 00 86 87 e3 00 01:35:11.580 READ DMA c8 00 00 00 98 00 03 36 00 86 ef e3 00 01:35:11.580 READ DMA c8 00 00 00 a0 00 03 35 00 86 8f e3 00 01:35:11.673 READ DMA Error 55 [14] occurred at disk power-on lifetime: 5051 hours (210 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 00:34:35.960 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 00:34:35.927 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 00:34:35.920 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 00:34:36.020 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 00:34:36.019 READ DMA Error 54 [13] occurred at disk power-on lifetime: 5051 hours (210 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 20 00 01 1c 00 42 ff e1 00 00:34:31.069 READ DMA ca 00 00 00 08 00 00 45 00 fc 77 e0 00 00:34:31.068 WRITE DMA ca 00 00 00 0a 00 02 4b 00 b5 47 e2 00 00:34:31.068 WRITE DMA ca 00 00 00 08 00 00 da 00 04 9f e0 00 00:34:31.063 WRITE DMA ca 00 00 00 10 00 00 09 00 0b 0f e0 00 00:34:31.063 WRITE DMA Error 53 [12] occurred at disk power-on lifetime: 5047 hours (210 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 01:39:01.010 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 01:39:01.011 READ DMA Error 52 [11] occurred at disk power-on lifetime: 5079 hours (211 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 40 00 01 1c 00 42 df e1 00 01:35:11.583 READ DMA c8 00 00 00 08 00 00 32 00 ae b7 e0 00 01:35:11.581 READ DMA c8 00 00 00 48 00 03 37 00 86 87 e3 00 01:35:11.580 READ DMA c8 00 00 00 98 00 03 36 00 86 ef e3 00 01:35:11.580 READ DMA c8 00 00 00 a0 00 03 35 00 86 8f e3 00 01:35:11.673 READ DMA Error 51 [10] occurred at disk power-on lifetime: 5051 hours (210 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 1d 00 42 0c e1 00 Error: UNC at LBA = 0x11d00420c = 4781523468 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 01 1d 00 42 0c e1 00 00:34:35.960 READ DMA c8 00 00 00 01 00 01 1d 00 42 0b e1 00 00:34:35.927 READ DMA c8 00 00 00 01 00 01 1d 00 42 0a e1 00 00:34:35.920 READ DMA c8 00 00 00 01 00 01 1d 00 42 09 e1 00 00:34:36.020 READ DMA c8 00 00 00 01 00 01 1d 00 42 08 e1 00 00:34:36.019 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS