/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P80 Device Model: SAMSUNG SP1213N Serial Number: -- Firmware Version: TL100-30 User Capacity: 120 060 444 672 bytes [120 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Mon May 16 02:30:52 2016 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 5040) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 094 051 - 1 3 Spin_Up_Time POS--- 100 099 025 - 5696 4 Start_Stop_Count -O--CK 089 089 000 - 11230 5 Reallocated_Sector_Ct PO--CK 100 100 011 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Half_Minutes -O--CK 094 094 000 - 31616h+32m 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 163 12 Power_Cycle_Count -O--CK 095 095 000 - 6037 194 Temperature_Celsius -O---K 154 079 000 - 28 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 484095 196 Reallocated_Event_Count -O--CK 095 095 000 - 12 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Total_Offl_Uncorrectabl ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 8 200 Multi_Zone_Error_Rate -O-R-- 100 100 051 - 0 201 Soft_Read_Error_Rate -O-R-- 100 100 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x06 SL R/O 2 SMART self-test log 0x80-0x9f SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 24973 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24973 occurred at disk power-on lifetime: 31535 hours (1313 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 30 c0 3c 82 eb Error: UNC 48 sectors at LBA = 0x0b823cc0 = 193084608 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 30 c0 3c 82 eb 00 07:29:52.313 READ DMA c8 00 a8 d0 e7 e8 e8 00 07:29:52.313 READ DMA c8 00 08 d8 55 82 eb 00 07:29:52.313 READ DMA c8 00 10 c0 55 82 eb 00 07:29:52.313 READ DMA c8 00 58 48 d8 e8 e8 00 07:29:52.313 READ DMA Error 24972 occurred at disk power-on lifetime: 31527 hours (1313 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 40 c0 3c 82 eb Error: UNC 64 sectors at LBA = 0x0b823cc0 = 193084608 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 40 c0 3c 82 eb 00 03:57:26.375 READ DMA c8 00 40 80 3c 82 eb 00 03:57:26.375 READ DMA c8 00 40 40 3c 82 eb 00 03:57:26.375 READ DMA c8 00 40 00 3c 82 eb 00 03:57:26.375 READ DMA c8 00 40 c0 3b 82 eb 00 03:57:26.375 READ DMA Error 24971 occurred at disk power-on lifetime: 31525 hours (1313 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 40 c0 3c 82 eb Error: UNC 64 sectors at LBA = 0x0b823cc0 = 193084608 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 40 c0 3c 82 eb 00 01:41:54.063 READ DMA c8 00 40 80 3c 82 eb 00 01:41:54.000 READ DMA c8 00 40 40 3c 82 eb 00 01:41:54.000 READ DMA c8 00 40 00 3c 82 eb 00 01:41:54.000 READ DMA c8 00 40 c0 3b 82 eb 00 01:41:54.000 READ DMA Error 24970 occurred at disk power-on lifetime: 31431 hours (1309 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 d8 3c 82 eb Error: UNC 8 sectors at LBA = 0x0b823cd8 = 193084632 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 d8 3c 82 eb 00 03:35:42.688 READ DMA c8 00 08 28 ba 68 eb 00 03:35:42.688 READ DMA c8 00 08 f0 a8 74 eb 00 03:35:42.688 READ DMA c8 00 08 b8 57 69 eb 00 03:35:42.688 READ DMA c8 00 08 c0 a8 74 eb 00 03:35:42.688 READ DMA Error 24969 occurred at disk power-on lifetime: 31429 hours (1309 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 10 d0 3c 82 eb Error: UNC 16 sectors at LBA = 0x0b823cd0 = 193084624 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 10 d0 3c 82 eb 00 01:06:22.188 READ DMA c8 00 10 80 09 82 eb 00 01:06:22.188 READ DMA c8 00 10 f0 15 82 eb 00 01:06:22.125 READ DMA c8 00 08 e0 15 82 eb 00 01:06:22.125 READ DMA c8 00 20 c0 a5 81 eb 00 01:06:22.125 READ DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 90% 31578 - # 2 Extended offline Completed: read failure 00% 31534 132275718 # 3 Extended offline Completed: read failure 00% 31470 132275718 # 4 Extended offline Completed: read failure 00% 31424 132275718 # 5 Extended offline Completed: read failure 00% 31375 132275718 # 6 Extended offline Completed: read failure 00% 31260 132275718 # 7 Extended offline Completed: read failure 00% 31148 132275718 # 8 Extended offline Completed: read failure 00% 31079 132275718 # 9 Extended offline Completed: read failure 00% 31009 132275718 Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD800JD-00JNC0 Serial Number: -- Firmware Version: 05.01C05 User Capacity: 80 026 361 856 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Mon May 16 02:30:53 2016 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Unknown SCT Status format version 1, should be 2 or 3. Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 35) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 14 3 Spin_Up_Time PO---- 174 159 021 - 2283 4 Start_Stop_Count -O--CK 095 095 000 - 5126 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 076 076 000 - 18110 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4801 194 Temperature_Celsius -O---K 104 078 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 775 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 15 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15 occurred at disk power-on lifetime: 17311 hours (721 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 54 73 3a 93 e1 Error: UNC 84 sectors at LBA = 0x01933a73 = 26425971 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 47 3a 93 01 68 00:14:47.960 READ DMA ca 00 80 17 42 86 01 68 00:14:47.960 WRITE DMA c8 00 08 ff 07 9d 00 68 00:14:47.955 READ DMA c8 00 08 b7 36 62 00 68 00:14:47.945 READ DMA c8 00 03 97 d1 1a 00 68 00:14:47.915 READ DMA Error 14 occurred at disk power-on lifetime: 17311 hours (721 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 54 73 3a 93 e1 Error: UNC 84 sectors at LBA = 0x01933a73 = 26425971 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 47 3a 93 01 68 00:14:45.800 READ DMA ca 00 80 97 41 86 01 68 00:14:45.800 WRITE DMA c8 00 08 3f 09 9d 00 68 00:14:45.795 READ DMA c8 00 08 29 dd 93 00 68 00:14:45.780 READ DMA ca 00 08 2f 00 5e 00 68 00:14:45.780 WRITE DMA Error 13 occurred at disk power-on lifetime: 17311 hours (721 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 54 73 3a 93 e1 Error: UNC 84 sectors at LBA = 0x01933a73 = 26425971 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 47 3a 93 01 68 00:14:43.230 READ DMA c8 00 20 49 72 82 01 68 00:14:43.225 READ DMA ca 00 80 77 79 4d 01 68 00:14:43.220 WRITE DMA c8 00 1c 47 54 8b 00 68 00:14:43.205 READ DMA c8 00 02 31 2a 77 00 68 00:14:43.195 READ DMA Error 12 occurred at disk power-on lifetime: 17311 hours (721 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 54 73 3a 93 e1 Error: UNC 84 sectors at LBA = 0x01933a73 = 26425971 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 47 3a 93 01 68 00:14:41.210 READ DMA c8 00 18 34 79 82 01 68 00:14:41.195 READ DMA ca 00 80 f7 78 4d 01 68 00:14:41.195 WRITE DMA c8 00 38 b9 29 77 00 68 00:14:41.175 READ DMA c8 00 08 a7 a8 f9 02 68 00:14:41.160 READ DMA Error 11 occurred at disk power-on lifetime: 17311 hours (721 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 54 73 3a 93 e1 Error: UNC 84 sectors at LBA = 0x01933a73 = 26425971 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 47 3a 93 01 68 00:14:39.035 READ DMA c8 00 30 11 72 82 01 68 00:14:39.025 READ DMA ca 00 80 77 78 4d 01 68 00:14:39.025 WRITE DMA c8 00 40 f1 29 77 00 68 00:14:39.010 READ DMA ca 00 20 8f 91 5e 00 68 00:14:39.005 WRITE DMA SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 80% 18065 - # 2 Extended offline Completed without error 00% 18019 - # 3 Extended offline Completed without error 00% 17948 - # 4 Extended offline Completed without error 00% 17900 - # 5 Extended offline Completed without error 00% 17846 - # 6 Extended offline Completed without error 00% 17718 - # 7 Extended offline Completed without error 00% 17596 - # 8 Extended offline Completed: read failure 90% 17522 23685665 # 9 Extended offline Completed without error 00% 17448 - #10 Short offline Completed without error 00% 15240 - 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 2 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Unknown SCT Status format version 1, should be 2 or 3. Unknown SCT Status format version 1, should be 2 or 3. SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD3200AAJS-00V4A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.01D05 User Capacity: 320 071 851 520 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon May 16 02:30:53 2016 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 79) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 13 3 Spin_Up_Time POS--K 144 142 021 - 3791 4 Start_Stop_Count -O--CK 099 099 000 - 1390 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 089 089 000 - 8512 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1389 192 Power-Off_Retract_Count -O--CK 200 200 000 - 599 193 Load_Cycle_Count -O--CK 200 200 000 - 790 194 Temperature_Celsius -O---K 108 096 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 199 199 000 - 75 198 Offline_Uncorrectable ----CK 199 199 000 - 75 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 80 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 32 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 32 [7] occurred at disk power-on lifetime: 8496 hours (354 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 05 58 a9 00 e0 00 Error: UNC at LBA = 0x0558a900 = 89696512 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 00 05 58 a9 00 e0 00 00:17:43.783 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 05 58 a8 00 e0 00 00:17:43.782 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 05 58 a7 00 e0 00 00:17:43.781 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 05 58 a6 00 e0 00 00:17:43.780 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 05 58 a5 00 e0 00 00:17:43.778 READ VERIFY SECTOR(S) EXT Error 31 [6] occurred at disk power-on lifetime: 8373 hours (348 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 01:53:53.775 READ DMA EXT 35 00 00 00 08 00 00 05 58 a4 d7 e0 08 01:53:53.775 WRITE DMA EXT 35 00 00 00 08 00 00 05 58 a4 37 e0 08 01:53:53.775 WRITE DMA EXT 25 00 00 00 08 00 00 03 94 b0 6f e0 08 01:53:53.763 READ DMA EXT 35 00 00 00 80 00 00 01 49 df 5f e0 08 01:53:53.763 WRITE DMA EXT Error 30 [5] occurred at disk power-on lifetime: 8373 hours (348 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 01:53:51.897 READ DMA EXT 35 00 00 00 08 00 00 05 58 a9 6f e0 08 01:53:51.896 WRITE DMA EXT 35 00 00 00 80 00 00 01 49 dc 5f e0 08 01:53:51.896 WRITE DMA EXT 35 00 00 00 80 00 00 01 49 db df e0 08 01:53:51.896 WRITE DMA EXT 35 00 00 00 80 00 00 01 49 db 5f e0 08 01:53:51.895 WRITE DMA EXT Error 29 [4] occurred at disk power-on lifetime: 8373 hours (348 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 01:53:50.036 READ DMA EXT 25 00 00 00 20 00 00 00 60 7f 1f e0 08 01:53:50.029 READ DMA EXT 25 00 00 00 20 00 00 00 61 14 ff e0 08 01:53:50.028 READ DMA EXT 35 00 00 00 08 00 00 00 60 77 67 e0 08 01:53:50.027 WRITE DMA EXT 25 00 00 00 20 00 00 00 61 14 1f e0 08 01:53:50.027 READ DMA EXT Error 28 [3] occurred at disk power-on lifetime: 8372 hours (348 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 00:30:37.838 READ DMA EXT 35 00 00 00 08 00 00 02 c6 e6 c7 e0 08 00:30:37.837 WRITE DMA EXT 35 00 00 00 80 00 00 01 3f 4b df e0 08 00:30:37.837 WRITE DMA EXT 35 00 00 00 80 00 00 01 3f 4b 5f e0 08 00:30:37.836 WRITE DMA EXT 35 00 00 00 80 00 00 01 3f 4a df e0 08 00:30:37.836 WRITE DMA EXT Error 27 [2] occurred at disk power-on lifetime: 8372 hours (348 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 00:30:35.874 READ DMA EXT 25 00 00 00 20 00 00 02 c6 e6 bf e0 08 00:30:35.855 READ DMA EXT 35 00 00 00 80 00 00 01 3f 48 df e0 08 00:30:35.854 WRITE DMA EXT 35 00 00 00 80 00 00 01 3f 48 5f e0 08 00:30:35.854 WRITE DMA EXT 35 00 00 00 80 00 00 01 3f 47 df e0 08 00:30:35.854 WRITE DMA EXT Error 26 [1] occurred at disk power-on lifetime: 8372 hours (348 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 58 a9 7f e0 00 Error: UNC 32 sectors at LBA = 0x0558a97f = 89696639 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 58 a9 7f e0 08 00:30:34.057 READ DMA EXT 25 00 00 00 20 00 00 00 61 14 ff e0 08 00:30:34.056 READ DMA EXT 25 00 00 00 20 00 00 00 61 14 1f e0 08 00:30:34.054 READ DMA EXT 25 00 00 00 20 00 00 00 61 12 df e0 08 00:30:34.054 READ DMA EXT 25 00 00 00 20 00 00 00 61 12 7f e0 08 00:30:34.042 READ DMA EXT Error 25 [0] occurred at disk power-on lifetime: 8309 hours (346 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 05 58 a9 80 40 00 Error: UNC at LBA = 0x0558a980 = 89696640 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 05 58 a9 7f 40 00 00:09:16.347 READ FPDMA QUEUED 60 00 01 00 10 00 00 05 8d c4 a8 40 00 00:09:06.762 READ FPDMA QUEUED 60 00 08 00 08 00 00 05 58 a9 7f 40 00 00:09:06.762 READ FPDMA QUEUED 60 00 01 00 10 00 00 00 00 00 00 40 00 00:09:04.358 READ FPDMA QUEUED 60 00 08 00 08 00 00 05 58 a9 7f 40 00 00:09:04.358 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 23/35 Celsius Lifetime Min/Max Temperature: ?/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (38) Index Estimated Time Temperature Celsius 39 2016-05-15 18:33 33 ************** ... ..(151 skipped). .. ************** 191 2016-05-15 21:05 33 ************** 192 2016-05-15 21:06 34 *************** ... ..(103 skipped). .. *************** 296 2016-05-15 22:50 34 *************** 297 2016-05-15 22:51 ? - 298 2016-05-15 22:52 23 **** 299 2016-05-15 22:53 24 ***** 300 2016-05-15 22:54 25 ****** 301 2016-05-15 22:55 25 ****** 302 2016-05-15 22:56 25 ****** 303 2016-05-15 22:57 26 ******* 304 2016-05-15 22:58 26 ******* 305 2016-05-15 22:59 27 ******** 306 2016-05-15 23:00 27 ******** 307 2016-05-15 23:01 28 ********* 308 2016-05-15 23:02 28 ********* 309 2016-05-15 23:03 29 ********** ... ..( 3 skipped). .. ********** 313 2016-05-15 23:07 29 ********** 314 2016-05-15 23:08 30 *********** ... ..( 2 skipped). .. *********** 317 2016-05-15 23:11 30 *********** 318 2016-05-15 23:12 31 ************ ... ..( 4 skipped). .. ************ 323 2016-05-15 23:17 31 ************ 324 2016-05-15 23:18 32 ************* ... ..( 13 skipped). .. ************* 338 2016-05-15 23:32 32 ************* 339 2016-05-15 23:33 33 ************** ... ..( 3 skipped). .. ************** 343 2016-05-15 23:37 33 ************** 344 2016-05-15 23:38 34 *************** ... ..( 5 skipped). .. *************** 350 2016-05-15 23:44 34 *************** 351 2016-05-15 23:45 35 **************** ... ..( 36 skipped). .. **************** 388 2016-05-16 00:22 35 **************** 389 2016-05-16 00:23 31 ************ ... ..( 16 skipped). .. ************ 406 2016-05-16 00:40 31 ************ 407 2016-05-16 00:41 32 ************* ... ..( 44 skipped). .. ************* 452 2016-05-16 01:26 32 ************* 453 2016-05-16 01:27 33 ************** ... ..( 62 skipped). .. ************** 38 2016-05-16 02:30 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5453 Vendor specific