/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9320325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0002SDM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Mar 18 14:05:38 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 099 006 - 244066828 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 090 090 020 - 10433 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 33 7 Seek_Error_Rate POSR-- 082 060 030 - 8952344247 9 Power_On_Hours -O--CK 100 086 000 - 463 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 090 037 020 - 10342 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 095 095 000 - 5 188 Command_Timeout -O--CK 100 098 000 - 12885229588 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 074 056 045 - 26 (Min/Max 23/26) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 576 192 Power-Off_Retract_Count -O--CK 100 100 000 - 4 193 Load_Cycle_Count -O--CK 001 001 000 - 279028 194 Temperature_Celsius -O---K 026 044 000 - 26 (255 248 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 069 055 000 - 244066828 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 12276 hours (511 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 c9 00 31 39 00 00 Error: UNC at LBA = 0x2c9003139 = 11962167609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 02 c9 00 31 38 40 00 00:00:14.016 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 00:00:13.874 READ LOG EXT 60 00 00 00 08 00 02 c9 00 31 38 40 00 00:00:11.585 READ FPDMA QUEUED 60 00 00 00 08 00 02 c9 00 31 30 40 00 00:00:11.579 READ FPDMA QUEUED 60 00 00 00 08 00 02 9f 00 30 48 40 00 00:00:11.578 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 12276 hours (511 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 c9 00 31 39 00 00 Error: UNC at LBA = 0x2c9003139 = 11962167609 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 02 c9 00 31 38 40 00 00:00:11.585 READ FPDMA QUEUED 60 00 00 00 08 00 02 c9 00 31 30 40 00 00:00:11.579 READ FPDMA QUEUED 60 00 00 00 08 00 02 9f 00 30 48 40 00 00:00:11.578 READ FPDMA QUEUED 60 00 00 00 08 00 02 9f 00 30 c8 40 00 00:00:11.578 READ FPDMA QUEUED 60 00 00 00 08 00 02 9f 00 30 40 40 00 00:00:11.578 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 2214 hours (92 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 04 ac 00 d6 a8 00 00 Error: WP at LBA = 0x4ac00d6a8 = 20065605288 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 06 dc 00 7d 20 40 00 00:34:46.805 WRITE FPDMA QUEUED 60 00 00 00 40 00 04 ac 00 d6 a8 40 00 00:34:46.627 READ FPDMA QUEUED 61 00 00 00 07 00 02 a0 00 20 10 40 00 00:34:46.370 WRITE FPDMA QUEUED 61 00 00 00 20 00 06 dc 00 7d 00 40 00 00:34:46.223 WRITE FPDMA QUEUED 61 00 00 00 20 00 06 db 00 7d e0 40 00 00:34:46.223 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 1298 hours (54 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 04 42 00 ab 78 00 00 Error: UNC at LBA = 0x44200ab78 = 18287209336 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 60 00 04 42 00 ab 78 40 00 00:16:23.962 READ FPDMA QUEUED 61 00 00 00 20 00 04 42 00 ab 50 40 00 00:16:23.821 WRITE FPDMA QUEUED 61 00 00 00 20 00 04 42 00 ab 30 40 00 00:16:23.800 WRITE FPDMA QUEUED 61 00 00 01 00 00 08 b0 00 57 20 40 00 00:16:23.800 WRITE FPDMA QUEUED 61 00 00 01 00 00 08 af 00 57 20 40 00 00:16:23.799 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 23/26 Celsius Lifetime Min/Max Temperature: -8/44 Celsius Under/Over Temperature Limit Count: 0/6 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (59) Index Estimated Time Temperature Celsius 60 2019-03-18 11:58 37 ****************** ... ..( 31 skipped). .. ****************** 92 2019-03-18 12:30 37 ****************** 93 2019-03-18 12:31 38 ******************* 94 2019-03-18 12:32 38 ******************* 95 2019-03-18 12:33 37 ****************** 96 2019-03-18 12:34 37 ****************** 97 2019-03-18 12:35 38 ******************* 98 2019-03-18 12:36 38 ******************* 99 2019-03-18 12:37 38 ******************* 100 2019-03-18 12:38 37 ****************** 101 2019-03-18 12:39 37 ****************** 102 2019-03-18 12:40 38 ******************* ... ..( 11 skipped). .. ******************* 114 2019-03-18 12:52 38 ******************* 115 2019-03-18 12:53 39 ******************** ... ..( 17 skipped). .. ******************** 5 2019-03-18 13:11 39 ******************** 6 2019-03-18 13:12 40 ********************* 7 2019-03-18 13:13 40 ********************* 8 2019-03-18 13:14 40 ********************* 9 2019-03-18 13:15 39 ******************** 10 2019-03-18 13:16 40 ********************* 11 2019-03-18 13:17 39 ******************** ... ..( 10 skipped). .. ******************** 22 2019-03-18 13:28 39 ******************** 23 2019-03-18 13:29 38 ******************* 24 2019-03-18 13:30 38 ******************* 25 2019-03-18 13:31 39 ******************** 26 2019-03-18 13:32 38 ******************* ... ..( 21 skipped). .. ******************* 48 2019-03-18 13:54 38 ******************* 49 2019-03-18 13:55 37 ****************** 50 2019-03-18 13:56 38 ******************* 51 2019-03-18 13:57 37 ****************** 52 2019-03-18 13:58 38 ******************* 53 2019-03-18 13:59 ? - 54 2019-03-18 14:00 23 **** 55 2019-03-18 14:01 24 ***** 56 2019-03-18 14:02 24 ***** 57 2019-03-18 14:03 25 ****** 58 2019-03-18 14:04 25 ****** 59 2019-03-18 14:05 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS