/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD403LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CT100-13 User Capacity: 400 087 375 360 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Mon Sep 11 20:34:37 2017 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7232) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 123) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 100 100 015 - 7616 4 Start_Stop_Count -O--CK 080 080 000 - 20221 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 1 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 32972 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 091 091 000 - 9332 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 4670522 187 Reported_Uncorrect -O--CK 096 096 000 - 196613 188 Command_Timeout -O--CK 098 098 000 - 217 190 Airflow_Temperature_Cel -O---K 065 051 000 - 35 194 Temperature_Celsius -O---K 133 088 000 - 35 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 4670522 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Total_Pending_Sectors -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 100 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead Device Error Count: 878 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 878 [5] occurred at disk power-on lifetime: 31140 hours (1297 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 00 00 01 00 00 00 00 00 00 e0 00 11:31:53.875 READ DMA ef 00 03 00 42 00 00 00 00 00 00 a0 00 11:31:46.813 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 11:31:46.750 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 a0 00 11:31:46.625 NOP [Abort queued commands] e0 5a ff 79 3e 00 00 00 00 00 02 a0 00 06:45:48.188 STANDBY IMMEDIATE Error 877 [4] occurred at disk power-on lifetime: 30561 hours (1273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 00 00 01 00 00 00 00 00 00 e0 00 00:15:35.938 READ DMA ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:15:28.688 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:15:28.688 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 a0 00 00:15:28.563 NOP [Abort queued commands] 35 4c ff 0e 12 00 00 01 06 13 00 e0 00 00:15:20.813 WRITE DMA EXT Error 876 [3] occurred at disk power-on lifetime: 29900 hours (1245 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 00 00 01 00 00 00 00 00 00 e0 00 00:01:04.188 READ DMA ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:00:56.875 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:56.813 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 a0 00 00:00:56.688 NOP [Abort queued commands] 35 89 ff 00 c4 00 00 01 c2 0b 00 e0 00 00:00:48.813 WRITE DMA EXT Error 875 [2] occurred at disk power-on lifetime: 29900 hours (1245 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 00 00 01 00 00 00 00 00 00 e0 00 00:51:05.625 READ DMA ef 00 03 00 42 00 00 00 00 00 00 a0 00 00:50:58.313 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:58.250 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 a0 00 00:50:58.125 NOP [Abort queued commands] 35 e6 ff 2e 90 00 00 01 c2 0c 00 e0 00 00:50:50.250 WRITE DMA EXT Error 874 [1] occurred at disk power-on lifetime: 28404 hours (1183 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 03 00 00 01 00 00 00 00 00 00 e0 00 06:36:04.063 READ DMA ef 00 03 00 42 00 00 00 00 00 00 a0 00 06:35:56.813 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 00 06:35:56.813 IDENTIFY DEVICE 00 00 00 00 01 00 00 00 00 00 01 a0 00 06:35:56.688 NOP [Abort queued commands] 35 a9 ff 6a 66 00 00 01 c7 ac 01 e0 00 06:35:48.750 WRITE DMA EXT Error 873 [0] occurred at disk power-on lifetime: 26266 hours (1094 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 00 9c bf 50 e0 00 Error: ICRC, ABRT 256 sectors at LBA = 0x009cbf50 = 10272592 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 00 9c bf 50 e0 00 00:00:32.625 READ DMA EXT 25 00 00 01 00 00 00 00 9c be 50 e0 00 00:00:32.625 READ DMA EXT 25 00 00 01 00 00 00 00 9c bd 50 e0 00 00:00:32.625 READ DMA EXT 25 00 00 01 00 00 00 00 9c bc 50 e0 00 00:00:32.625 READ DMA EXT 25 00 00 01 00 00 00 00 9c bb 50 e0 00 00:00:32.625 READ DMA EXT Error 872 [7] occurred at disk power-on lifetime: 26040 hours (1085 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 03 56 41 c0 e0 00 Error: ICRC, ABRT 256 sectors at LBA = 0x035641c0 = 55984576 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 03 56 41 c0 e0 00 00:01:16.625 READ DMA EXT 25 00 00 01 00 00 00 03 56 40 c0 e0 00 00:01:16.625 READ DMA EXT 25 00 00 01 00 00 00 03 56 3f c0 e0 00 00:01:16.625 READ DMA EXT 25 00 00 01 00 00 00 03 56 3e c0 e0 00 00:01:16.625 READ DMA EXT 25 00 00 01 00 00 00 03 56 3d c0 e0 00 00:01:16.625 READ DMA EXT Error 871 [6] occurred at disk power-on lifetime: 25560 hours (1065 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 02 cf 41 c0 e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x02cf41c0 = 47137216 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 02 cf 41 c0 e0 00 00:05:21.438 READ DMA EXT 25 00 00 00 08 00 00 02 cf 41 80 e0 00 00:05:21.438 READ DMA EXT 25 00 00 00 40 00 00 02 cf 41 80 e0 00 00:05:21.438 READ DMA EXT 25 00 00 00 08 00 00 02 cf 41 40 e0 00 00:05:21.438 READ DMA EXT 25 00 00 00 30 00 00 03 2b 20 88 e0 00 00:05:21.438 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 35/36 Celsius Lifetime Min/Max Temperature: 10/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (49) Index Estimated Time Temperature Celsius 50 2017-09-11 18:27 33 ************** 51 2017-09-11 18:28 33 ************** 52 2017-09-11 18:29 33 ************** 53 2017-09-11 18:30 35 **************** ... ..( 6 skipped). .. **************** 60 2017-09-11 18:37 35 **************** 61 2017-09-11 18:38 28 ********* 62 2017-09-11 18:39 27 ******** 63 2017-09-11 18:40 27 ******** 64 2017-09-11 18:41 28 ********* 65 2017-09-11 18:42 28 ********* 66 2017-09-11 18:43 28 ********* 67 2017-09-11 18:44 29 ********** 68 2017-09-11 18:45 29 ********** 69 2017-09-11 18:46 29 ********** 70 2017-09-11 18:47 30 *********** 71 2017-09-11 18:48 30 *********** 72 2017-09-11 18:49 31 ************ 73 2017-09-11 18:50 31 ************ 74 2017-09-11 18:51 31 ************ 75 2017-09-11 18:52 32 ************* ... ..( 4 skipped). .. ************* 80 2017-09-11 18:57 32 ************* 81 2017-09-11 18:58 33 ************** ... ..( 2 skipped). .. ************** 84 2017-09-11 19:01 33 ************** 85 2017-09-11 19:02 35 **************** ... ..( 8 skipped). .. **************** 94 2017-09-11 19:11 35 **************** 95 2017-09-11 19:12 36 ***************** ... ..( 17 skipped). .. ***************** 113 2017-09-11 19:30 36 ***************** 114 2017-09-11 19:31 35 **************** ... ..( 3 skipped). .. **************** 118 2017-09-11 19:35 35 **************** 119 2017-09-11 19:36 26 ******* 120 2017-09-11 19:37 36 ***************** 121 2017-09-11 19:38 35 **************** 122 2017-09-11 19:39 36 ***************** 123 2017-09-11 19:40 35 **************** ... ..( 2 skipped). .. **************** 126 2017-09-11 19:43 35 **************** 127 2017-09-11 19:44 36 ***************** ... ..( 6 skipped). .. ***************** 6 2017-09-11 19:51 36 ***************** 7 2017-09-11 19:52 31 ************ 8 2017-09-11 19:53 35 **************** 9 2017-09-11 19:54 36 ***************** ... ..( 2 skipped). .. ***************** 12 2017-09-11 19:57 36 ***************** 13 2017-09-11 19:58 35 **************** 14 2017-09-11 19:59 35 **************** 15 2017-09-11 20:00 35 **************** 16 2017-09-11 20:01 36 ***************** 17 2017-09-11 20:02 35 **************** 18 2017-09-11 20:03 36 ***************** 19 2017-09-11 20:04 35 **************** ... ..( 2 skipped). .. **************** 22 2017-09-11 20:07 35 **************** 23 2017-09-11 20:08 36 ***************** 24 2017-09-11 20:09 36 ***************** 25 2017-09-11 20:10 35 **************** 26 2017-09-11 20:11 36 ***************** 27 2017-09-11 20:12 35 **************** 28 2017-09-11 20:13 36 ***************** 29 2017-09-11 20:14 35 **************** 30 2017-09-11 20:15 35 **************** 31 2017-09-11 20:16 36 ***************** 32 2017-09-11 20:17 35 **************** 33 2017-09-11 20:18 36 ***************** ... ..( 3 skipped). .. ***************** 37 2017-09-11 20:22 36 ***************** 38 2017-09-11 20:23 35 **************** 39 2017-09-11 20:24 35 **************** 40 2017-09-11 20:25 35 **************** 41 2017-09-11 20:26 36 ***************** 42 2017-09-11 20:27 35 **************** ... ..( 5 skipped). .. **************** 48 2017-09-11 20:33 35 **************** 49 2017-09-11 20:34 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific