/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.32-generic-5rosa2021.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000524AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: JC4B User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Apr 7 09:00:44 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 172) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 202544732 3 Spin_Up_Time PO---- 100 100 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 559 5 Reallocated_Sector_Ct PO--CK 036 036 036 NOW 2648 7 Seek_Error_Rate POSR-- 064 060 030 - 184792173539 9 Power_On_Hours -O--CK 050 050 000 - 44214 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 582 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 086 086 000 - 14 188 Command_Timeout -O--CK 100 096 000 - 51540393997 189 High_Fly_Writes -O-RCK 098 098 000 - 2 190 Airflow_Temperature_Cel -O---K 071 044 045 Past 29 (0 1 29 18 0) 194 Temperature_Celsius -O---K 029 056 000 - 29 (0 1 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 025 021 000 - 202544732 197 Current_Pending_Sector -O--C- 100 097 000 - 15 198 Offline_Uncorrectable ----C- 100 097 000 - 15 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 7263 (141 43 0) 241 Total_LBAs_Written ------ 100 253 000 - 1390427703 242 Total_LBAs_Read ------ 100 253 000 - 3565860530 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 7736 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7736 [15] occurred at disk power-on lifetime: 43539 hours (1814 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 66 70 f7 6a 00 00 Error: UNC at LBA = 0x6670f76a = 1718679402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 66 70 f7 68 40 00 00:00:47.036 READ FPDMA QUEUED 60 00 00 00 08 00 00 66 70 f7 60 40 00 00:00:47.034 READ FPDMA QUEUED 60 00 00 00 08 00 00 66 70 f7 58 40 00 00:00:47.034 READ FPDMA QUEUED 60 00 00 00 08 00 00 66 70 f7 50 40 00 00:00:47.034 READ FPDMA QUEUED 60 00 00 00 08 00 00 66 70 f7 48 40 00 00:00:47.034 READ FPDMA QUEUED Error 7735 [14] occurred at disk power-on lifetime: 43539 hours (1814 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 66 70 f7 6a 00 00 Error: UNC at LBA = 0x6670f76a = 1718679402 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 66 70 53 b8 40 00 00:00:43.209 READ FPDMA QUEUED 60 00 00 02 00 00 00 66 70 51 b8 40 00 00:00:43.199 READ FPDMA QUEUED 60 00 00 01 00 00 00 69 67 db 40 40 00 00:00:43.194 READ FPDMA QUEUED 60 00 00 01 00 00 00 69 67 da 40 40 00 00:00:43.145 READ FPDMA QUEUED 60 00 00 01 00 00 00 69 67 d9 40 40 00 00:00:43.085 READ FPDMA QUEUED Error 7734 [13] occurred at disk power-on lifetime: 42359 hours (1764 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6e 3b 07 82 00 00 Error: UNC at LBA = 0x6e3b0782 = 1849362306 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 6e 3b 07 80 40 00 00:00:41.911 READ FPDMA QUEUED 60 00 00 00 08 00 00 6e 3b 07 78 40 00 00:00:41.910 READ FPDMA QUEUED 60 00 00 00 08 00 00 6e 3b 07 70 40 00 00:00:41.910 READ FPDMA QUEUED 60 00 00 00 08 00 00 6e 3b 07 68 40 00 00:00:41.909 READ FPDMA QUEUED 60 00 00 00 08 00 00 6e 3b 07 60 40 00 00:00:41.909 READ FPDMA QUEUED Error 7733 [12] occurred at disk power-on lifetime: 42359 hours (1764 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 6e 3b 07 82 00 00 Error: UNC at LBA = 0x6e3b0782 = 1849362306 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 6e 3a d5 e0 40 00 00:00:38.888 READ FPDMA QUEUED 60 00 00 02 00 00 00 6e 3a d3 e0 40 00 00:00:38.873 READ FPDMA QUEUED 60 00 00 01 00 00 00 6d 87 74 d8 40 00 00:00:38.861 READ FPDMA QUEUED 60 00 00 02 00 00 00 6d 87 72 d8 40 00 00:00:38.845 READ FPDMA QUEUED 60 00 00 00 20 00 00 6a 6d 4e 30 40 00 00:00:38.836 READ FPDMA QUEUED Error 7732 [11] occurred at disk power-on lifetime: 39820 hours (1659 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2b f4 2c db 00 00 Error: UNC at LBA = 0x2bf42cdb = 737422555 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 2b f4 2c d8 40 00 00:00:49.320 READ FPDMA QUEUED 60 00 00 00 08 00 00 2b f4 2c d0 40 00 00:00:49.320 READ FPDMA QUEUED 60 00 00 00 08 00 00 2b f4 2c c8 40 00 00:00:49.318 READ FPDMA QUEUED 60 00 00 00 08 00 00 2b f4 2c c0 40 00 00:00:49.317 READ FPDMA QUEUED 60 00 00 00 08 00 00 2b f4 2c b8 40 00 00:00:49.316 READ FPDMA QUEUED Error 7731 [10] occurred at disk power-on lifetime: 39820 hours (1659 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2b f4 2c db 00 00 Error: UNC at LBA = 0x2bf42cdb = 737422555 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 2b f4 27 50 40 00 00:00:46.332 READ FPDMA QUEUED 60 00 00 01 00 00 00 2b f4 26 50 40 00 00:00:46.102 READ FPDMA QUEUED 60 00 00 01 00 00 00 2b f4 25 50 40 00 00:00:46.085 READ FPDMA QUEUED 60 00 00 01 00 00 00 2b f4 24 50 40 00 00:00:46.070 READ FPDMA QUEUED 60 00 00 01 00 00 00 2b f4 23 50 40 00 00:00:46.053 READ FPDMA QUEUED Error 7730 [9] occurred at disk power-on lifetime: 37904 hours (1579 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 0a e9 4f 00 00 Error: UNC at LBA = 0x000ae94f = 715087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 0a e9 4f 40 00 00:02:02.485 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:02:02.479 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:02:02.477 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:02:02.477 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:02:02.476 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 7729 [8] occurred at disk power-on lifetime: 37904 hours (1579 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 0a e9 4f 00 00 Error: WP at LBA = 0x000ae94f = 715087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 00 e4 00 4f 40 00 00:01:29.015 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 e0 00 4f 40 00 00:01:29.015 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 bc 00 4f 40 00 00:01:29.014 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 ac 00 4f 40 00 00:01:29.014 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 a8 00 4f 40 00 00:01:29.014 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: unknown failure 90% 44061 0 # 2 Extended offline Completed: unknown failure 90% 43927 0 # 3 Extended offline Completed: unknown failure 90% 43767 0 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 18/29 Celsius Lifetime Min/Max Temperature: 0/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2022-04-02 04:00 35 **************** ... ..( 7 skipped). .. **************** 55 2022-04-02 11:52 35 **************** 56 2022-04-02 12:51 36 ***************** 57 2022-04-02 13:50 35 **************** 58 2022-04-02 14:49 36 ***************** ... ..( 5 skipped). .. ***************** 64 2022-04-02 20:43 36 ***************** 65 2022-04-02 21:42 28 ********* 66 2022-04-02 22:41 29 ********** 67 2022-04-02 23:40 29 ********** 68 2022-04-03 00:39 33 ************** 69 2022-04-03 01:38 34 *************** 70 2022-04-03 02:37 34 *************** 71 2022-04-03 03:36 34 *************** 72 2022-04-03 04:35 33 ************** 73 2022-04-03 05:34 34 *************** 74 2022-04-03 06:33 35 **************** ... ..( 3 skipped). .. **************** 78 2022-04-03 10:29 35 **************** 79 2022-04-03 11:28 34 *************** ... ..( 8 skipped). .. *************** 88 2022-04-03 20:19 34 *************** 89 2022-04-03 21:18 30 *********** 90 2022-04-03 22:17 33 ************** 91 2022-04-03 23:16 33 ************** 92 2022-04-04 00:15 34 *************** 93 2022-04-04 01:14 34 *************** 94 2022-04-04 02:13 34 *************** 95 2022-04-04 03:12 ? - 96 2022-04-04 04:11 18 - 97 2022-04-04 05:10 ? - 98 2022-04-04 06:09 28 ********* 99 2022-04-04 07:08 28 ********* 100 2022-04-04 08:07 33 ************** 101 2022-04-04 09:06 34 *************** 102 2022-04-04 10:05 35 **************** 103 2022-04-04 11:04 34 *************** 104 2022-04-04 12:03 34 *************** 105 2022-04-04 13:02 ? - 106 2022-04-04 14:01 18 - 107 2022-04-04 15:00 18 - 108 2022-04-04 15:59 29 ********** 109 2022-04-04 16:58 33 ************** 110 2022-04-04 17:57 33 ************** 111 2022-04-04 18:56 34 *************** 112 2022-04-04 19:55 33 ************** 113 2022-04-04 20:54 ? - 114 2022-04-04 21:53 19 - 115 2022-04-04 22:52 19 - 116 2022-04-04 23:51 ? - 117 2022-04-05 00:50 21 ** 118 2022-04-05 01:49 21 ** 119 2022-04-05 02:48 32 ************* 120 2022-04-05 03:47 34 *************** 121 2022-04-05 04:46 35 **************** ... ..( 20 skipped). .. **************** 14 2022-04-06 01:25 35 **************** 15 2022-04-06 02:24 33 ************** 16 2022-04-06 03:23 34 *************** 17 2022-04-06 04:22 35 **************** 18 2022-04-06 05:21 34 *************** 19 2022-04-06 06:20 34 *************** 20 2022-04-06 07:19 35 **************** ... ..( 17 skipped). .. **************** 38 2022-04-07 01:01 35 **************** 39 2022-04-07 02:00 31 ************ 40 2022-04-07 02:59 32 ************* 41 2022-04-07 03:58 32 ************* 42 2022-04-07 04:57 34 *************** 43 2022-04-07 05:56 34 *************** 44 2022-04-07 06:55 ? - 45 2022-04-07 07:54 18 - 46 2022-04-07 08:53 18 - SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.32-generic-5rosa2021.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSDPR-CX300-120 Serial Number: -- Firmware Version: SBFM61.3 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Apr 7 09:00:44 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 10130 12 Power_Cycle_Count -O--C- 100 100 000 - 1980 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 100 100 010 - 158 173 Unknown_Attribute -O--C- 100 100 000 - 5242984 192 Power-Off_Retract_Count -O--C- 100 100 000 - 127 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 Unknown_Attribute PO-R-- 100 100 050 - 0 231 Unknown_SSD_Attribute PO--C- 100 100 000 - 97 241 Total_LBAs_Written -O--C- 100 100 000 - 7904 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 9977 - # 2 Extended offline Completed without error 00% 9843 - # 3 Extended offline Completed without error 00% 9683 - # 4 Short offline Completed without error 00% 6413 - # 5 Short offline Completed without error 00% 6404 - # 6 Short offline Completed without error 00% 6384 - # 7 Short offline Completed without error 00% 6368 - # 8 Short offline Completed without error 00% 6354 - # 9 Short offline Completed without error 00% 6344 - #10 Short offline Completed without error 00% 6334 - #11 Short offline Completed without error 00% 6325 - #12 Short offline Completed without error 00% 6314 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1980 --- Lifetime Power-On Resets 0x01 0x010 4 10130 --- Power-on Hours 0x01 0x018 6 16576095023 --- Logical Sectors Written 0x01 0x028 6 15834682225 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 12295 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 2 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC