/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545032A7E380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GGBOAC90 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Oct 1 23:32:33 2018 +04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 90) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 195 195 040 - 276 3 Spin_Up_Time POS--- 227 227 033 - 1 4 Start_Stop_Count -O--C- 098 098 000 - 3773 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 40 9 Power_On_Hours -O--C- 083 083 000 - 7632 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 3471 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 373 193 Load_Cycle_Count -O--C- 071 071 000 - 297893 194 Temperature_Celsius -O---- 176 176 000 - 34 (Min/Max 13/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 18 197 Current_Pending_Sector -O---K 100 100 000 - 8 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 54 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 54 [1] occurred at disk power-on lifetime: 6066 hours (252 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 78 00 00 00 05 8b 80 00 00 Error: UNC at LBA = 0x00058b80 = 363392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 28 00 00 24 c7 86 00 40 00 00:00:49.435 READ FPDMA QUEUED 60 00 08 00 20 00 00 03 10 c0 c0 40 00 00:00:49.409 READ FPDMA QUEUED 60 00 08 00 18 00 00 03 10 ae f8 40 00 00:00:49.409 READ FPDMA QUEUED 60 00 18 00 10 00 00 00 05 c8 00 40 00 00:00:49.409 READ FPDMA QUEUED 60 01 00 00 08 00 00 00 05 8a f8 40 00 00:00:49.408 READ FPDMA QUEUED Error 53 [0] occurred at disk power-on lifetime: 6060 hours (252 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 78 00 00 00 05 8b 80 00 00 Error: UNC at LBA = 0x00058b80 = 363392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 08 00 00 00 05 8a f8 40 00 00:13:11.543 READ FPDMA QUEUED 60 00 08 00 00 00 00 03 10 6a c0 40 00 00:13:11.543 READ FPDMA QUEUED 60 01 00 00 f0 00 00 00 05 89 f8 40 00 00:13:11.542 READ FPDMA QUEUED 60 00 08 00 e8 00 00 03 10 6a b8 40 00 00:13:11.541 READ FPDMA QUEUED 60 01 00 00 e0 00 00 00 05 88 f8 40 00 00:13:11.541 READ FPDMA QUEUED Error 52 [3] occurred at disk power-on lifetime: 6059 hours (252 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 78 00 00 00 05 8b 80 00 00 Error: UNC at LBA = 0x00058b80 = 363392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 03 10 b1 b8 40 00 00:01:27.054 READ FPDMA QUEUED 60 00 18 00 90 00 00 00 05 c8 00 40 00 00:01:27.054 READ FPDMA QUEUED 60 00 28 00 88 00 00 25 42 df c8 40 00 00:01:27.032 READ FPDMA QUEUED 60 00 38 00 80 00 00 25 42 df 88 40 00 00:01:27.032 READ FPDMA QUEUED 60 00 78 00 78 00 00 25 42 df 08 40 00 00:01:27.032 READ FPDMA QUEUED Error 51 [2] occurred at disk power-on lifetime: 6003 hours (250 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 78 00 00 00 05 8b 80 00 00 Error: UNC at LBA = 0x00058b80 = 363392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 03 10 c0 88 40 00 00:01:38.184 READ FPDMA QUEUED 60 01 00 00 78 00 00 00 05 8a f8 40 00 00:01:38.184 READ FPDMA QUEUED 60 00 08 00 70 00 00 03 10 c0 80 40 00 00:01:38.183 READ FPDMA QUEUED 60 01 00 00 68 00 00 00 05 89 f8 40 00 00:01:38.183 READ FPDMA QUEUED 60 00 08 00 60 00 00 03 10 c0 78 40 00 00:01:38.183 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 7371 363392 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 34/34 Celsius Lifetime Min/Max Temperature: 13/47 Celsius Lifetime Average Temperature: 35 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (126) Index Estimated Time Temperature Celsius 127 2018-10-01 21:25 32 ************* ... ..( 4 skipped). .. ************* 4 2018-10-01 21:30 32 ************* 5 2018-10-01 21:31 33 ************** ... ..( 2 skipped). .. ************** 8 2018-10-01 21:34 33 ************** 9 2018-10-01 21:35 32 ************* 10 2018-10-01 21:36 32 ************* 11 2018-10-01 21:37 32 ************* 12 2018-10-01 21:38 33 ************** 13 2018-10-01 21:39 33 ************** 14 2018-10-01 21:40 34 *************** ... ..( 4 skipped). .. *************** 19 2018-10-01 21:45 34 *************** 20 2018-10-01 21:46 33 ************** 21 2018-10-01 21:47 34 *************** 22 2018-10-01 21:48 34 *************** 23 2018-10-01 21:49 33 ************** 24 2018-10-01 21:50 34 *************** 25 2018-10-01 21:51 34 *************** 26 2018-10-01 21:52 35 **************** 27 2018-10-01 21:53 35 **************** 28 2018-10-01 21:54 35 **************** 29 2018-10-01 21:55 34 *************** ... ..( 3 skipped). .. *************** 33 2018-10-01 21:59 34 *************** 34 2018-10-01 22:00 35 **************** 35 2018-10-01 22:01 34 *************** 36 2018-10-01 22:02 34 *************** 37 2018-10-01 22:03 35 **************** 38 2018-10-01 22:04 35 **************** 39 2018-10-01 22:05 36 ***************** 40 2018-10-01 22:06 36 ***************** 41 2018-10-01 22:07 36 ***************** 42 2018-10-01 22:08 37 ****************** ... ..( 4 skipped). .. ****************** 47 2018-10-01 22:13 37 ****************** 48 2018-10-01 22:14 38 ******************* ... ..( 8 skipped). .. ******************* 57 2018-10-01 22:23 38 ******************* 58 2018-10-01 22:24 39 ******************** ... ..( 7 skipped). .. ******************** 66 2018-10-01 22:32 39 ******************** 67 2018-10-01 22:33 38 ******************* 68 2018-10-01 22:34 38 ******************* 69 2018-10-01 22:35 37 ****************** ... ..( 4 skipped). .. ****************** 74 2018-10-01 22:40 37 ****************** 75 2018-10-01 22:41 38 ******************* 76 2018-10-01 22:42 ? - 77 2018-10-01 22:43 37 ****************** 78 2018-10-01 22:44 37 ****************** 79 2018-10-01 22:45 36 ***************** 80 2018-10-01 22:46 36 ***************** 81 2018-10-01 22:47 36 ***************** 82 2018-10-01 22:48 35 **************** 83 2018-10-01 22:49 35 **************** 84 2018-10-01 22:50 35 **************** 85 2018-10-01 22:51 ? - 86 2018-10-01 22:52 36 ***************** ... ..( 4 skipped). .. ***************** 91 2018-10-01 22:57 36 ***************** 92 2018-10-01 22:58 35 **************** 93 2018-10-01 22:59 36 ***************** ... ..( 2 skipped). .. ***************** 96 2018-10-01 23:02 36 ***************** 97 2018-10-01 23:03 ? - 98 2018-10-01 23:04 36 ***************** 99 2018-10-01 23:05 36 ***************** 100 2018-10-01 23:06 36 ***************** 101 2018-10-01 23:07 ? - 102 2018-10-01 23:08 35 **************** ... ..( 3 skipped). .. **************** 106 2018-10-01 23:12 35 **************** 107 2018-10-01 23:13 34 *************** 108 2018-10-01 23:14 34 *************** 109 2018-10-01 23:15 34 *************** 110 2018-10-01 23:16 ? - 111 2018-10-01 23:17 33 ************** ... ..( 3 skipped). .. ************** 115 2018-10-01 23:21 33 ************** 116 2018-10-01 23:22 34 *************** ... ..( 5 skipped). .. *************** 122 2018-10-01 23:28 34 *************** 123 2018-10-01 23:29 ? - 124 2018-10-01 23:30 ? - 125 2018-10-01 23:31 34 *************** 126 2018-10-01 23:32 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS