/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-23-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD5000LPVX-22V0TT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun May 21 06:49:40 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 113) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 388 3 Spin_Up_Time POS--K 155 149 021 - 1225 4 Start_Stop_Count -O--CK 097 097 000 - 3835 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 096 096 000 - 3373 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1229 191 G-Sense_Error_Rate -O--CK 001 001 000 - 101 192 Power-Off_Retract_Count -O--CK 200 200 000 - 597 193 Load_Cycle_Count -O--CK 196 196 000 - 14093 194 Temperature_Celsius -O---K 106 087 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 406 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 406 [21] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 78 00 00 00 21 46 28 40 00 00:30:29.992 READ FPDMA QUEUED 60 00 08 00 70 00 00 07 a9 fa d8 40 00 00:30:29.991 READ FPDMA QUEUED 60 00 08 00 68 00 00 07 a9 a7 78 40 00 00:30:29.991 READ FPDMA QUEUED 60 00 08 00 60 00 00 07 a9 a6 b0 40 00 00:30:29.981 READ FPDMA QUEUED 60 00 08 00 58 00 00 07 a9 a6 a0 40 00 00:30:29.981 READ FPDMA QUEUED Error 405 [20] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 b8 00 00 07 a9 fa 00 40 00 00:29:11.050 READ FPDMA QUEUED 60 00 02 00 b0 00 00 07 a9 fa cc 40 00 00:29:11.024 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:29:11.023 READ LOG EXT 60 01 00 00 a8 00 00 07 a9 fa 00 40 00 00:29:07.545 READ FPDMA QUEUED 60 00 02 00 a0 00 00 07 a9 fa aa 40 00 00:29:07.519 READ FPDMA QUEUED Error 404 [19] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 a8 00 00 07 a9 fa 00 40 00 00:29:07.545 READ FPDMA QUEUED 60 00 02 00 a0 00 00 07 a9 fa aa 40 00 00:29:07.519 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:29:07.517 READ LOG EXT 60 01 00 00 98 00 00 07 a9 fa 00 40 00 00:29:04.040 READ FPDMA QUEUED 60 00 02 00 90 00 00 07 a9 fa 8c 40 00 00:29:04.012 READ FPDMA QUEUED Error 403 [18] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 98 00 00 07 a9 fa 00 40 00 00:29:04.040 READ FPDMA QUEUED 60 00 02 00 90 00 00 07 a9 fa 8c 40 00 00:29:04.012 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:29:04.010 READ LOG EXT 60 01 00 00 88 00 00 07 a9 fa 00 40 00 00:29:00.533 READ FPDMA QUEUED 60 00 02 00 80 00 00 07 a9 fa 7e 40 00 00:29:00.507 READ FPDMA QUEUED Error 402 [17] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 88 00 00 07 a9 fa 00 40 00 00:29:00.533 READ FPDMA QUEUED 60 00 02 00 80 00 00 07 a9 fa 7e 40 00 00:29:00.507 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:29:00.505 READ LOG EXT 60 01 00 00 78 00 00 07 a9 fa 00 40 00 00:28:57.039 READ FPDMA QUEUED 60 00 02 00 70 00 00 07 a9 fa 76 40 00 00:28:57.013 READ FPDMA QUEUED Error 401 [16] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 78 00 00 07 a9 fa 00 40 00 00:28:57.039 READ FPDMA QUEUED 60 00 02 00 70 00 00 07 a9 fa 76 40 00 00:28:57.013 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:28:57.011 READ LOG EXT 60 01 00 00 68 00 00 07 a9 fa 00 40 00 00:28:53.544 READ FPDMA QUEUED 60 00 02 00 60 00 00 07 a9 fa 44 40 00 00:28:53.518 READ FPDMA QUEUED Error 400 [15] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 68 00 00 07 a9 fa 00 40 00 00:28:53.544 READ FPDMA QUEUED 60 00 02 00 60 00 00 07 a9 fa 44 40 00 00:28:53.518 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:28:53.516 READ LOG EXT 60 01 00 00 58 00 00 07 a9 fa 00 40 00 00:28:50.038 READ FPDMA QUEUED 60 00 02 00 50 00 00 07 a9 fa 2e 40 00 00:28:50.012 READ FPDMA QUEUED Error 399 [14] occurred at disk power-on lifetime: 2885 hours (120 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 07 a9 fa d8 40 00 Error: UNC at LBA = 0x07a9fad8 = 128580312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 58 00 00 07 a9 fa 00 40 00 00:28:50.038 READ FPDMA QUEUED 60 00 02 00 50 00 00 07 a9 fa 2e 40 00 00:28:50.012 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:28:50.010 READ LOG EXT 60 01 00 00 48 00 00 07 a9 fa 00 40 00 00:28:46.532 READ FPDMA QUEUED 60 00 02 00 40 00 00 07 a9 fa 24 40 00 00:28:46.507 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 21/38 Celsius Lifetime Min/Max Temperature: 12/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (17) Index Estimated Time Temperature Celsius 18 2023-05-21 04:42 36 ***************** ... ..( 2 skipped). .. ***************** 21 2023-05-21 04:45 36 ***************** 22 2023-05-21 04:46 35 **************** ... ..( 40 skipped). .. **************** 63 2023-05-21 05:27 35 **************** 64 2023-05-21 05:28 34 *************** ... ..( 22 skipped). .. *************** 87 2023-05-21 05:51 34 *************** 88 2023-05-21 05:52 35 **************** 89 2023-05-21 05:53 35 **************** 90 2023-05-21 05:54 34 *************** 91 2023-05-21 05:55 35 **************** 92 2023-05-21 05:56 35 **************** 93 2023-05-21 05:57 35 **************** 94 2023-05-21 05:58 34 *************** ... ..( 2 skipped). .. *************** 97 2023-05-21 06:01 34 *************** 98 2023-05-21 06:02 35 **************** ... ..( 4 skipped). .. **************** 103 2023-05-21 06:07 35 **************** 104 2023-05-21 06:08 34 *************** ... ..( 2 skipped). .. *************** 107 2023-05-21 06:11 34 *************** 108 2023-05-21 06:12 35 **************** ... ..( 3 skipped). .. **************** 112 2023-05-21 06:16 35 **************** 113 2023-05-21 06:17 34 *************** 114 2023-05-21 06:18 35 **************** 115 2023-05-21 06:19 35 **************** 116 2023-05-21 06:20 34 *************** 117 2023-05-21 06:21 35 **************** ... ..( 5 skipped). .. **************** 123 2023-05-21 06:27 35 **************** 124 2023-05-21 06:28 34 *************** ... ..( 4 skipped). .. *************** 1 2023-05-21 06:33 34 *************** 2 2023-05-21 06:34 35 **************** ... ..( 3 skipped). .. **************** 6 2023-05-21 06:38 35 **************** 7 2023-05-21 06:39 36 ***************** 8 2023-05-21 06:40 36 ***************** 9 2023-05-21 06:41 37 ****************** 10 2023-05-21 06:42 37 ****************** 11 2023-05-21 06:43 37 ****************** 12 2023-05-21 06:44 36 ***************** ... ..( 3 skipped). .. ***************** 16 2023-05-21 06:48 36 ***************** 17 2023-05-21 06:49 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 30830 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 17 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 24980 Vendor specific