/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.15-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Intenso SSD Sata III Serial Number: -- Firmware Version: S0222A0 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jul 25 15:19:51 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 750 12 Power_Cycle_Count -O--CK 100 100 050 - 1758 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 9 164 Unknown_Attribute -O--CK 100 100 050 - 10097 165 Unknown_Attribute -O--CK 100 100 050 - 37 166 Unknown_Attribute -O--CK 100 100 050 - 2 167 Unknown_Attribute -O--CK 100 100 050 - 20 168 Unknown_Attribute -O--CK 100 100 050 - 7000 169 Unknown_Attribute -O--CK 100 100 050 - 100 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 1224 194 Temperature_Celsius -O---K 100 100 050 - 0 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 16960 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 18218 242 Total_LBAs_Read ----CK 100 100 050 - 32287 245 Unknown_Attribute -O--CK 100 100 050 - 19071 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] log entry is empty SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 734 - # 2 Short offline Completed without error 00% 670 - # 3 Extended offline Completed without error 00% 659 - # 4 Short offline Completed without error 00% 655 - # 5 Short offline Completed without error 00% 651 - # 6 Short offline Completed without error 00% 648 - # 7 Short offline Completed without error 00% 639 - # 8 Short offline Completed without error 00% 629 - # 9 Short offline Completed without error 00% 608 - #10 Short offline Completed without error 00% 606 - #11 Short offline Completed without error 00% 605 - #12 Short offline Completed without error 00% 603 - #13 Extended offline Completed without error 00% 601 - #14 Short offline Completed without error 00% 593 - #15 Short offline Completed without error 00% 593 - #16 Short offline Completed without error 00% 588 - #17 Short offline Completed without error 00% 580 - #18 Short offline Completed without error 00% 544 - #19 Short offline Completed without error 00% 541 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1758 --- Lifetime Power-On Resets 0x01 0x010 4 750 --- Power-on Hours 0x01 0x018 6 1193956657 --- Logical Sectors Written 0x01 0x020 6 9733 --- Number of Write Commands 0x01 0x028 6 2116003493 --- Logical Sectors Read 0x01 0x030 6 30321 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 1 R_ERR response for non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.15-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9320423AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0003SDM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jul 25 15:19:51 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM level is: 127 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 75) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 086 006 - 178355403 3 Spin_Up_Time PO---- 099 097 085 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3439 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 076 060 030 - 13049707477 9 Power_On_Hours -O--CK 094 094 000 - 5564 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 098 037 020 - 2985 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 3882 188 Command_Timeout -O--CK 100 100 000 - 1 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 070 054 045 - 30 (Min/Max 24/30) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 3 192 Power-Off_Retract_Count -O--CK 100 100 000 - 71 193 Load_Cycle_Count -O--CK 052 052 000 - 97177 194 Temperature_Celsius -O---K 030 046 000 - 30 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 054 039 000 - 178355403 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 5446 (13 221 0) 241 Total_LBAs_Written ------ 100 253 000 - 3063986249 242 Total_LBAs_Read ------ 100 253 000 - 1616668923 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2763 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2763 [2] occurred at disk power-on lifetime: 5036 hours (209 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:57.701 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 02:04:57.597 READ LOG EXT 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:54.935 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 02:04:54.898 READ LOG EXT 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:52.137 READ FPDMA QUEUED Error 2762 [1] occurred at disk power-on lifetime: 5036 hours (209 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:54.935 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 02:04:54.898 READ LOG EXT 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:52.137 READ FPDMA QUEUED 61 00 00 00 08 00 02 00 00 34 38 40 00 02:04:52.137 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 02:04:51.906 READ LOG EXT Error 2761 [0] occurred at disk power-on lifetime: 5036 hours (209 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:52.137 READ FPDMA QUEUED 61 00 00 00 08 00 02 00 00 34 38 40 00 02:04:52.137 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 02:04:51.906 READ LOG EXT 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:49.271 READ FPDMA QUEUED 60 00 00 00 18 00 02 13 00 20 e0 40 00 02:04:49.267 READ FPDMA QUEUED Error 2760 [19] occurred at disk power-on lifetime: 5036 hours (209 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 02 56 00 36 80 40 00 02:04:49.271 READ FPDMA QUEUED 60 00 00 00 18 00 02 13 00 20 e0 40 00 02:04:49.267 READ FPDMA QUEUED 61 00 00 00 10 00 02 36 00 37 00 40 00 02:04:49.264 WRITE FPDMA QUEUED 60 00 00 00 10 00 02 f1 00 21 80 40 00 02:04:49.263 READ FPDMA QUEUED 61 00 00 00 20 00 02 35 00 37 e0 40 00 02:04:49.262 WRITE FPDMA QUEUED Error 2759 [18] occurred at disk power-on lifetime: 5015 hours (208 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:51.788 READ FPDMA QUEUED 60 00 00 00 08 00 01 bc 00 e7 00 40 00 00:52:51.786 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:52:51.785 READ LOG EXT 60 00 00 00 8c 00 03 76 00 22 48 40 00 00:52:49.125 READ FPDMA QUEUED 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:49.124 READ FPDMA QUEUED Error 2758 [17] occurred at disk power-on lifetime: 5015 hours (208 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 8c 00 03 76 00 22 48 40 00 00:52:49.125 READ FPDMA QUEUED 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:49.124 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:52:49.079 READ LOG EXT 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:46.420 READ FPDMA QUEUED 60 00 00 00 08 00 03 76 00 22 40 40 00 00:52:46.411 READ FPDMA QUEUED Error 2757 [16] occurred at disk power-on lifetime: 5015 hours (208 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: WP at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 02 00 00 34 88 40 00 00:52:43.600 WRITE FPDMA QUEUED 60 00 00 00 08 00 03 76 00 22 40 40 00 00:52:43.599 READ FPDMA QUEUED 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:43.598 READ FPDMA QUEUED 61 00 00 00 08 00 01 38 00 dd 60 40 00 00:52:43.597 WRITE FPDMA QUEUED 61 00 00 00 08 00 01 5d 00 ee 00 40 00 00:52:43.597 WRITE FPDMA QUEUED Error 2756 [15] occurred at disk power-on lifetime: 5015 hours (208 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 56 00 36 88 00 00 Error: UNC at LBA = 0x256003688 = 10032789128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 02 56 00 36 80 40 00 00:52:40.741 READ FPDMA QUEUED 61 00 00 00 18 00 02 f2 00 33 58 40 00 00:52:40.739 WRITE FPDMA QUEUED 60 00 00 00 18 00 02 8d 00 1b 00 40 00 00:52:40.737 READ FPDMA QUEUED 61 00 00 00 20 00 13 ce 00 97 60 40 00 00:52:40.736 WRITE FPDMA QUEUED 61 00 00 00 20 00 13 2a 00 98 a0 40 00 00:52:40.736 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5544 - # 2 Short offline Completed without error 00% 5470 - # 3 Extended offline Completed without error 00% 5460 - # 4 Short offline Completed without error 00% 5454 - # 5 Short offline Completed without error 00% 5449 - # 6 Short offline Completed without error 00% 5445 - # 7 Short offline Completed without error 00% 5441 - # 8 Short offline Completed without error 00% 5431 - # 9 Short offline Completed without error 00% 5407 - #10 Short offline Completed without error 00% 5405 - #11 Short offline Completed without error 00% 5404 - #12 Short offline Completed without error 00% 5403 - #13 Extended offline Completed without error 00% 5401 - #14 Short offline Completed without error 00% 5390 - #15 Short offline Completed without error 00% 5390 - #16 Short offline Completed without error 00% 5384 - #17 Short offline Completed without error 00% 5375 - #18 Short offline Completed without error 00% 5332 - #19 Extended offline Completed without error 00% 5329 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 24/30 Celsius Lifetime Min/Max Temperature: 12/47 Celsius Specified Max Operating Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (28) Index Estimated Time Temperature Celsius 29 2021-07-25 13:12 31 ************ ... ..( 9 skipped). .. ************ 39 2021-07-25 13:22 31 ************ 40 2021-07-25 13:23 32 ************* 41 2021-07-25 13:24 32 ************* 42 2021-07-25 13:25 33 ************** ... ..( 8 skipped). .. ************** 51 2021-07-25 13:34 33 ************** 52 2021-07-25 13:35 34 *************** ... ..( 3 skipped). .. *************** 56 2021-07-25 13:39 34 *************** 57 2021-07-25 13:40 35 **************** ... ..( 9 skipped). .. **************** 67 2021-07-25 13:50 35 **************** 68 2021-07-25 13:51 36 ***************** 69 2021-07-25 13:52 36 ***************** 70 2021-07-25 13:53 35 **************** ... ..( 2 skipped). .. **************** 73 2021-07-25 13:56 35 **************** 74 2021-07-25 13:57 34 *************** ... ..( 4 skipped). .. *************** 79 2021-07-25 14:02 34 *************** 80 2021-07-25 14:03 33 ************** ... ..( 9 skipped). .. ************** 90 2021-07-25 14:13 33 ************** 91 2021-07-25 14:14 32 ************* ... ..( 7 skipped). .. ************* 99 2021-07-25 14:22 32 ************* 100 2021-07-25 14:23 33 ************** ... ..( 25 skipped). .. ************** 126 2021-07-25 14:49 33 ************** 127 2021-07-25 14:50 32 ************* ... ..( 4 skipped). .. ************* 4 2021-07-25 14:55 32 ************* 5 2021-07-25 14:56 ? - 6 2021-07-25 14:57 24 ***** 7 2021-07-25 14:58 24 ***** 8 2021-07-25 14:59 25 ****** 9 2021-07-25 15:00 25 ****** 10 2021-07-25 15:01 26 ******* 11 2021-07-25 15:02 26 ******* 12 2021-07-25 15:03 26 ******* 13 2021-07-25 15:04 27 ******** ... ..( 2 skipped). .. ******** 16 2021-07-25 15:07 27 ******** 17 2021-07-25 15:08 28 ********* ... ..( 3 skipped). .. ********* 21 2021-07-25 15:12 28 ********* 22 2021-07-25 15:13 29 ********** ... ..( 4 skipped). .. ********** 27 2021-07-25 15:18 29 ********** 28 2021-07-25 15:19 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS