/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD1600AAJS-75PSA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.06H05 User Capacity: 159 998 918 144 bytes [159 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon Oct 10 10:16:30 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4260) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 57) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 181 171 051 - 497015 3 Spin_Up_Time PO---- 162 160 021 - 2883 4 Start_Stop_Count -O--CK 099 099 000 - 1686 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 074 074 000 - 19039 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1316 192 Power-Off_Retract_Count -O--CK 200 200 000 - 155 193 Load_Cycle_Count -O--CK 200 200 000 - 1700 194 Temperature_Celsius -O---K 109 091 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 12 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 40676 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 40676 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 91 25 04 2c 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 7f 04 91 02 2c 25 00 00 00 00:00:34.568 NOP [Abort queued commands] 02 91 25 04 2c 00 08 00 77 00 00 00 02 00:04:33.553 [RESERVED] 00 08 00 00 67 04 91 02 2c 25 00 00 00 00:00:28.424 NOP [Abort queued commands] Error 40675 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 cd 25 04 22 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 af 04 ca 02 22 25 00 00 00 00:00:44.800 NOP [Abort queued commands] 02 c7 25 04 22 00 00 00 af 00 00 00 02 00:04:31.049 [RESERVED] 00 00 00 00 af 04 c6 02 22 25 00 00 00 00:00:44.800 NOP [Abort queued commands] Error 40674 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 af 25 03 68 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 7f 03 af 02 68 25 00 00 00 00:00:34.568 NOP [Abort queued commands] 02 af 25 03 68 00 08 00 77 00 00 00 02 00:03:43.407 [RESERVED] 00 08 00 00 67 03 af 02 68 25 00 00 00 00:00:28.424 NOP [Abort queued commands] Error 40673 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d5 25 03 5e 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 2f 03 d3 02 5e 25 00 00 00 00:00:12.032 NOP [Abort queued commands] 02 cf 25 03 5e 00 00 00 2f 00 00 00 02 00:03:40.881 [RESERVED] 00 00 00 00 2f 03 ce 02 5e 25 00 00 00 00:00:12.032 NOP [Abort queued commands] Error 40672 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1f 29 02 60 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 7f 02 1d 02 60 29 00 00 00 00:00:34.568 NOP [Abort queued commands] 02 1b 29 02 60 00 08 00 77 00 00 00 02 00:02:35.676 [RESERVED] 00 08 00 00 67 02 1a 02 60 29 00 00 00 00:00:28.424 NOP [Abort queued commands] Error 40671 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b9 29 02 40 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 af 02 94 02 40 29 00 00 00 00:00:44.800 NOP [Abort queued commands] 02 47 29 02 40 00 00 00 af 00 00 00 02 00:02:27.565 [RESERVED] 00 00 00 00 af 02 21 02 40 29 00 00 00 00:00:44.800 NOP [Abort queued commands] Error 40670 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0d 25 01 a4 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 7f 01 0d 02 a4 25 00 00 00 00:00:34.568 NOP [Abort queued commands] 02 0d 25 01 a4 00 08 00 77 00 00 00 02 00:01:47.533 [RESERVED] 00 08 00 00 67 01 0d 02 a4 25 00 00 00 00:00:28.424 NOP [Abort queued commands] Error 40669 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 33 25 01 9a 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 2f 01 32 02 9a 25 00 00 00 00:00:12.032 NOP [Abort queued commands] 02 2e 25 01 9a 00 00 00 2f 00 00 00 02 00:01:45.007 [RESERVED] 00 00 00 00 2f 01 2c 02 9a 25 00 00 00 00:00:12.032 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 32/34 Celsius Lifetime Min/Max Temperature: 34/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2016-10-10 08:09 34 *************** 115 2016-10-10 08:10 34 *************** 116 2016-10-10 08:11 34 *************** 117 2016-10-10 08:12 33 ************** ... ..( 10 skipped). .. ************** 0 2016-10-10 08:23 33 ************** 1 2016-10-10 08:24 32 ************* ... ..( 28 skipped). .. ************* 30 2016-10-10 08:53 32 ************* 31 2016-10-10 08:54 ? - 32 2016-10-10 08:55 23 **** 33 2016-10-10 08:56 23 **** 34 2016-10-10 08:57 24 ***** 35 2016-10-10 08:58 25 ****** 36 2016-10-10 08:59 25 ****** 37 2016-10-10 09:00 26 ******* 38 2016-10-10 09:01 26 ******* 39 2016-10-10 09:02 27 ******** 40 2016-10-10 09:03 27 ******** 41 2016-10-10 09:04 27 ******** 42 2016-10-10 09:05 28 ********* ... ..( 2 skipped). .. ********* 45 2016-10-10 09:08 28 ********* 46 2016-10-10 09:09 29 ********** 47 2016-10-10 09:10 29 ********** 48 2016-10-10 09:11 29 ********** 49 2016-10-10 09:12 30 *********** ... ..( 5 skipped). .. *********** 55 2016-10-10 09:18 30 *********** 56 2016-10-10 09:19 31 ************ ... ..( 7 skipped). .. ************ 64 2016-10-10 09:27 31 ************ 65 2016-10-10 09:28 32 ************* ... ..( 4 skipped). .. ************* 70 2016-10-10 09:33 32 ************* 71 2016-10-10 09:34 ? - 72 2016-10-10 09:35 33 ************** 73 2016-10-10 09:36 32 ************* 74 2016-10-10 09:37 33 ************** ... ..( 28 skipped). .. ************** 103 2016-10-10 10:06 33 ************** 104 2016-10-10 10:07 34 *************** ... ..( 8 skipped). .. *************** 113 2016-10-10 10:16 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 2448 Vendor specific