/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD321KJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CP100-12 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Sep 30 01:33:01 2015 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 5839) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 100) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 100 100 015 - 5632 4 Start_Stop_Count -O--CK 093 093 000 - 8027 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 1 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 20143 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4083 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 9878490 187 Reported_Uncorrect -O--CK 089 089 000 - 12 188 Command_Timeout -O--CK 098 098 000 - 289 190 Airflow_Temperature_Cel -O---K 070 056 000 - 30 194 Temperature_Celsius -O---K 145 106 000 - 31 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 9878490 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Total_Pending_Sectors -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 100 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 099 099 000 - 640 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x07) instead Device Error Count: 1053 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1053 [6] occurred at disk power-on lifetime: 20135 hours (838 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 20 00 00 1a d8 e2 e1 e0 00 Error: ABRT 32 sectors at LBA = 0x1ad8e2e1 = 450421473 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 1a d8 e2 e1 e0 00 00:01:17.250 READ DMA EXT 25 00 00 00 40 00 00 1a db d5 72 e0 00 00:01:16.625 READ DMA EXT 25 00 00 00 40 00 00 1a d5 6e e2 e0 00 00:01:16.625 READ DMA EXT 25 00 00 00 10 00 00 1a d5 ee 72 e0 00 00:01:16.625 READ DMA EXT 25 00 00 00 1c 00 00 1a d6 70 29 e0 00 00:01:16.625 READ DMA EXT Error 1052 [5] occurred at disk power-on lifetime: 20125 hours (838 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 68 00 00 17 07 16 e8 e0 00 Error: ABRT 104 sectors at LBA = 0x170716e8 = 386340584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 68 00 00 17 07 16 e8 e0 00 00:03:09.438 READ DMA EXT 25 00 00 00 48 00 00 17 1d fd b8 e0 00 00:03:08.813 READ DMA EXT 25 00 00 00 80 00 00 19 5f 39 48 e0 00 00:03:08.813 READ DMA EXT 25 00 00 00 80 00 00 19 5f 38 c8 e0 00 00:03:08.813 READ DMA EXT 25 00 00 00 80 00 00 19 5f 38 48 e0 00 00:03:08.813 READ DMA EXT Error 1051 [4] occurred at disk power-on lifetime: 20125 hours (838 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 40 00 00 16 f6 c5 a2 e0 00 Error: ABRT 64 sectors at LBA = 0x16f6c5a2 = 385271202 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 16 f6 c5 a2 e0 00 00:02:14.938 READ DMA EXT 25 00 00 00 20 00 00 16 f6 ca 75 e0 00 00:02:14.313 READ DMA EXT 25 00 00 00 40 00 00 16 f6 c6 ba e0 00 00:02:14.313 READ DMA EXT 25 00 00 00 20 00 00 16 f6 ca 95 e0 00 00:02:14.250 READ DMA EXT 25 00 00 00 40 00 00 17 05 3d ba e0 00 00:02:14.250 READ DMA EXT Error 1050 [3] occurred at disk power-on lifetime: 20114 hours (838 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 80 00 00 17 0e 90 c8 e0 00 Error: ABRT 128 sectors at LBA = 0x170e90c8 = 386830536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 17 0e 90 c8 e0 00 00:07:21.500 READ DMA EXT 25 00 00 00 40 00 00 17 0b 68 00 e0 00 00:07:20.813 READ DMA EXT 25 00 00 00 80 00 00 17 15 71 c8 e0 00 00:07:20.813 READ DMA EXT 25 00 00 00 08 00 00 17 15 71 c0 e0 00 00:07:20.813 READ DMA EXT 25 00 00 00 80 00 00 17 15 71 40 e0 00 00:07:20.813 READ DMA EXT Error 1049 [2] occurred at disk power-on lifetime: 20096 hours (837 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 08 00 00 17 01 9b d8 e0 00 Error: ABRT 8 sectors at LBA = 0x17019bd8 = 385981400 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 17 01 9b d8 e0 00 00:00:47.438 READ DMA EXT 25 00 00 00 20 00 00 16 f5 61 f8 e0 00 00:00:46.813 READ DMA EXT 25 00 00 00 40 00 00 17 19 da c0 e0 00 00:00:46.750 READ DMA EXT 25 00 00 00 60 00 00 17 16 ad 90 e0 00 00:00:46.750 READ DMA EXT 25 00 00 00 80 00 00 17 16 ad 10 e0 00 00:00:46.750 READ DMA EXT Error 1048 [1] occurred at disk power-on lifetime: 20091 hours (837 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 10 00 00 04 f5 79 e7 e0 00 Error: ABRT 16 sectors at LBA = 0x04f579e7 = 83196391 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 04 f5 79 e7 e0 00 01:26:37.063 READ DMA EXT 25 00 00 00 80 00 00 04 f5 6f 47 e0 00 01:26:36.438 READ DMA EXT 25 00 00 00 50 00 00 04 f6 20 7f e0 00 01:26:36.438 READ DMA EXT 25 00 00 00 80 00 00 04 f6 8b ef e0 00 01:26:36.438 READ DMA EXT 25 00 00 00 48 00 00 04 f6 8a 4f e0 00 01:26:36.438 READ DMA EXT Error 1047 [0] occurred at disk power-on lifetime: 20089 hours (837 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 40 00 00 17 04 73 f2 e0 00 Error: ABRT 64 sectors at LBA = 0x170473f2 = 386167794 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 17 04 73 f2 e0 00 04:30:45.875 READ DMA EXT 25 00 00 00 08 00 00 17 04 ab fa e0 00 04:30:45.188 READ DMA EXT 25 00 00 00 08 00 00 04 d7 10 6f e0 00 04:30:45.188 READ DMA EXT 25 00 00 00 08 00 00 04 d7 2c af e0 00 04:30:45.188 READ DMA EXT 25 00 00 00 08 00 00 04 d7 04 cf e0 00 04:30:45.188 READ DMA EXT Error 1046 [7] occurred at disk power-on lifetime: 20084 hours (836 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 40 00 00 1a e6 b8 92 e0 00 Error: ABRT 64 sectors at LBA = 0x1ae6b892 = 451328146 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 1a e6 b8 92 e0 00 00:01:23.625 READ DMA EXT 25 00 00 00 08 00 00 1a ef 15 28 e0 00 00:01:23.000 READ DMA EXT 25 00 00 00 40 00 00 1b ea 48 e2 e0 00 00:01:22.938 READ DMA EXT 25 00 00 00 08 00 00 1e df 23 50 e0 00 00:01:22.938 READ DMA EXT 25 00 00 00 40 00 00 1a e6 b9 3a e0 00 00:01:22.938 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Abort offline test Aborted by host 90% 13870 - # 2 Abort offline test Aborted by host 90% 13870 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 17/33 Celsius Lifetime Min/Max Temperature: 7/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (115) Index Estimated Time Temperature Celsius 116 2015-09-29 23:26 30 *********** ... ..( 32 skipped). .. *********** 21 2015-09-29 23:59 30 *********** 22 2015-09-30 00:00 31 ************ 23 2015-09-30 00:01 30 *********** 24 2015-09-30 00:02 30 *********** 25 2015-09-30 00:03 31 ************ 26 2015-09-30 00:04 31 ************ 27 2015-09-30 00:05 30 *********** 28 2015-09-30 00:06 31 ************ 29 2015-09-30 00:07 31 ************ 30 2015-09-30 00:08 31 ************ 31 2015-09-30 00:09 30 *********** 32 2015-09-30 00:10 30 *********** 33 2015-09-30 00:11 31 ************ 34 2015-09-30 00:12 31 ************ 35 2015-09-30 00:13 30 *********** 36 2015-09-30 00:14 31 ************ ... ..( 15 skipped). .. ************ 52 2015-09-30 00:30 31 ************ 53 2015-09-30 00:31 30 *********** 54 2015-09-30 00:32 30 *********** 55 2015-09-30 00:33 30 *********** 56 2015-09-30 00:34 31 ************ 57 2015-09-30 00:35 30 *********** 58 2015-09-30 00:36 31 ************ 59 2015-09-30 00:37 30 *********** 60 2015-09-30 00:38 30 *********** 61 2015-09-30 00:39 31 ************ 62 2015-09-30 00:40 31 ************ 63 2015-09-30 00:41 30 *********** 64 2015-09-30 00:42 31 ************ 65 2015-09-30 00:43 30 *********** 66 2015-09-30 00:44 31 ************ ... ..( 6 skipped). .. ************ 73 2015-09-30 00:51 31 ************ 74 2015-09-30 00:52 30 *********** 75 2015-09-30 00:53 31 ************ 76 2015-09-30 00:54 30 *********** 77 2015-09-30 00:55 31 ************ 78 2015-09-30 00:56 30 *********** 79 2015-09-30 00:57 31 ************ 80 2015-09-30 00:58 30 *********** ... ..( 2 skipped). .. *********** 83 2015-09-30 01:01 30 *********** 84 2015-09-30 01:02 31 ************ 85 2015-09-30 01:03 30 *********** ... ..( 3 skipped). .. *********** 89 2015-09-30 01:07 30 *********** 90 2015-09-30 01:08 31 ************ 91 2015-09-30 01:09 31 ************ 92 2015-09-30 01:10 31 ************ 93 2015-09-30 01:11 30 *********** 94 2015-09-30 01:12 31 ************ ... ..( 2 skipped). .. ************ 97 2015-09-30 01:15 31 ************ 98 2015-09-30 01:16 30 *********** 99 2015-09-30 01:17 30 *********** 100 2015-09-30 01:18 31 ************ 101 2015-09-30 01:19 31 ************ 102 2015-09-30 01:20 30 *********** ... ..( 12 skipped). .. *********** 115 2015-09-30 01:33 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific