/dev/nvme0n1 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.75-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: SCY SMM5T1G51200D 512GB Serial Number: -- Firmware Version: H220902a PCI Vendor/Subsystem ID: 0x1f03 IEEE OUI Identifier: 0x000000 Total NVM Capacity: 512,110,190,592 [512 GB] Unallocated NVM Capacity: 0 Controller ID: 0 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 512,110,190,592 [512 GB] Namespace 1 Utilization: 3,803,967,488 [3.80 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 000000 ... Local Time is: Thu Oct 12 17:13:50 2023 MSK Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x001f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Log Page Attributes (0x02): Cmd_Eff_Lg Maximum Data Transfer Size: 128 Pages Warning Comp. Temp. Threshold: 90 Celsius Critical Comp. Temp. Threshold: 95 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.50W - - 0 0 0 0 0 0 1 + 5.80W - - 1 1 1 1 0 0 2 + 3.60W - - 2 2 2 2 0 0 3 - 0.0500W - - 3 3 3 3 5000 10000 4 - 0.0025W - - 4 4 4 4 8000 45000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 40 Celsius Available Spare: 100% Available Spare Threshold: 1% Percentage Used: 0% Data Units Read: 66,605 [34.1 GB] Data Units Written: 67,612 [34.6 GB] Host Read Commands: 369,968 Host Write Commands: 147,592 Controller Busy Time: 4 Power Cycles: 10 Power On Hours: 1 Unsafe Shutdowns: 4 Media and Data Integrity Errors: 0 Error Information Log Entries: 12 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 40 Celsius Temperature Sensor 2: 32 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) Num ErrCount SQId CmdId Status PELoc LBA NSID VS 0 12 0 0x5011 0x2002 0x000 0 0 - 1 11 0 0x2014 0x2002 0x000 0 0 - /dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.75-generic-1rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 870 EVO 500GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: SVT01B6Q User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 12 17:13:50 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 099 099 000 - 121 12 Power_Cycle_Count -O--CK 099 099 000 - 875 177 Wear_Leveling_Count PO--C- 099 099 000 - 6 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 065 044 000 - 35 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 836 241 Total_LBAs_Written -O--CK 099 099 000 - 1528872275 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 27/35 Celsius Lifetime Min/Max Temperature: 21/56 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (0) Index Estimated Time Temperature Celsius 1 2023-10-11 20:00 ? - ... ..( 7 skipped). .. - 9 2023-10-11 21:20 ? - 10 2023-10-11 21:30 33 ************** 11 2023-10-11 21:40 ? - 12 2023-10-11 21:50 ? - 13 2023-10-11 22:00 33 ************** 14 2023-10-11 22:10 ? - ... ..( 4 skipped). .. - 19 2023-10-11 23:00 ? - 20 2023-10-11 23:10 32 ************* 21 2023-10-11 23:20 ? - 22 2023-10-11 23:30 33 ************** 23 2023-10-11 23:40 ? - 24 2023-10-11 23:50 34 *************** 25 2023-10-12 00:00 ? - ... ..( 7 skipped). .. - 33 2023-10-12 01:20 ? - 34 2023-10-12 01:30 30 *********** 35 2023-10-12 01:40 ? - 36 2023-10-12 01:50 34 *************** 37 2023-10-12 02:00 35 **************** 38 2023-10-12 02:10 ? - ... ..( 8 skipped). .. - 47 2023-10-12 03:40 ? - 48 2023-10-12 03:50 34 *************** 49 2023-10-12 04:00 ? - ... ..( 7 skipped). .. - 57 2023-10-12 05:20 ? - 58 2023-10-12 05:30 30 *********** 59 2023-10-12 05:40 34 *************** 60 2023-10-12 05:50 36 ***************** 61 2023-10-12 06:00 37 ****************** 62 2023-10-12 06:10 ? - 63 2023-10-12 06:20 ? - 64 2023-10-12 06:30 34 *************** 65 2023-10-12 06:40 36 ***************** 66 2023-10-12 06:50 38 ******************* 67 2023-10-12 07:00 ? - 68 2023-10-12 07:10 ? - 69 2023-10-12 07:20 37 ****************** 70 2023-10-12 07:30 ? - 71 2023-10-12 07:40 ? - 72 2023-10-12 07:50 26 ******* 73 2023-10-12 08:00 29 ********** 74 2023-10-12 08:10 31 ************ 75 2023-10-12 08:20 32 ************* 76 2023-10-12 08:30 ? - 77 2023-10-12 08:40 ? - 78 2023-10-12 08:50 29 ********** 79 2023-10-12 09:00 31 ************ 80 2023-10-12 09:10 32 ************* 81 2023-10-12 09:20 33 ************** 82 2023-10-12 09:30 ? - 83 2023-10-12 09:40 35 **************** 84 2023-10-12 09:50 35 **************** 85 2023-10-12 10:00 ? - 86 2023-10-12 10:10 36 ***************** 87 2023-10-12 10:20 ? - 88 2023-10-12 10:30 34 *************** 89 2023-10-12 10:40 37 ****************** 90 2023-10-12 10:50 37 ****************** 91 2023-10-12 11:00 38 ******************* 92 2023-10-12 11:10 38 ******************* 93 2023-10-12 11:20 39 ******************** 94 2023-10-12 11:30 39 ******************** 95 2023-10-12 11:40 ? - 96 2023-10-12 11:50 33 ************** 97 2023-10-12 12:00 34 *************** 98 2023-10-12 12:10 35 **************** 99 2023-10-12 12:20 35 **************** 100 2023-10-12 12:30 36 ***************** ... ..( 2 skipped). .. ***************** 103 2023-10-12 13:00 36 ***************** 104 2023-10-12 13:10 ? - 105 2023-10-12 13:20 ? - 106 2023-10-12 13:30 ? - 107 2023-10-12 13:40 31 ************ 108 2023-10-12 13:50 ? - 109 2023-10-12 14:00 35 **************** 110 2023-10-12 14:10 34 *************** 111 2023-10-12 14:20 ? - ... ..( 4 skipped). .. - 116 2023-10-12 15:10 ? - 117 2023-10-12 15:20 30 *********** 118 2023-10-12 15:30 ? - ... ..( 3 skipped). .. - 122 2023-10-12 16:10 ? - 123 2023-10-12 16:20 31 ************ 124 2023-10-12 16:30 33 ************** 125 2023-10-12 16:40 34 *************** 126 2023-10-12 16:50 ? - 127 2023-10-12 17:00 35 **************** 0 2023-10-12 17:10 35 **************** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 875 --- Lifetime Power-On Resets 0x01 0x010 4 121 --- Power-on Hours 0x01 0x018 6 1528872275 --- Logical Sectors Written 0x01 0x020 6 14877245 --- Number of Write Commands 0x01 0x028 6 2550908181 --- Logical Sectors Read 0x01 0x030 6 111214936 --- Number of Read Commands 0x01 0x038 6 2733000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 28 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC