/dev/sda smartctl 7.1 2019-12-30 r5022 [i686-linux-4.15.0-desktop-122.124.1rosa-i586] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Black Device Model: WDC WD1600BEKT-60A25T1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 03.01A03 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Oct 12 21:40:10 2021 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4560) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 57) minutes. SCT capabilities: (0x703f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 28 3 Spin_Up_Time POS--K 142 106 021 - 1866 4 Start_Stop_Count -O--CK 093 093 000 - 7566 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7461 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4700 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 072 000 - 28 188 Command_Timeout -O--CK 100 098 000 - 93 190 Airflow_Temperature_Cel -O---K 060 050 040 - 40 (Min/Max 40/41) 191 G-Sense_Error_Rate -O--CK 001 001 000 - 1574 192 Power-Off_Retract_Count -O--CK 200 200 000 - 0 193 Load_Cycle_Count -O--CK 179 179 000 - 65504 194 Temperature_Celsius -O---K 103 093 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 28 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 28 [3] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:18.932 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:18.932 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:16.782 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:16.782 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:14.686 READ FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:16.782 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:16.782 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:14.686 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:14.686 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:12.540 READ FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:14.686 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:14.686 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:12.540 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:12.540 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:10.470 READ FPDMA QUEUED Error 25 [0] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:12.540 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:12.540 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:10.470 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:10.470 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:08.394 READ FPDMA QUEUED Error 24 [23] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:10.470 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:10.470 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:08.394 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:08.394 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:06.304 READ FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:08.394 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:08.394 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:06.304 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:06.303 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:04.158 READ FPDMA QUEUED Error 22 [21] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:06.304 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:06.303 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:04.158 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:04.158 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:02.066 READ FPDMA QUEUED Error 21 [20] occurred at disk power-on lifetime: 4710 hours (196 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 e1 75 ab 40 00 Error: UNC at LBA = 0x02e175ab = 48330155 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:04.158 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:04.158 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:01:02.066 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:01:02.066 SET FEATURES [Enable write cache] 60 00 08 00 08 00 00 02 e1 75 a7 40 00 00:00:59.901 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6783 - # 2 Short offline Completed without error 00% 6115 - # 3 Short offline Completed without error 00% 6110 - # 4 Short offline Completed without error 00% 5100 - # 5 Short offline Aborted by host 90% 1856 - # 6 Short offline Completed without error 00% 1856 - # 7 Short offline Completed without error 00% 1856 - # 8 Short offline Completed without error 00% 1856 - # 9 Short offline Completed without error 00% 1856 - #10 Short offline Completed without error 00% 1856 - #11 Short offline Completed without error 00% 1856 - #12 Short offline Completed without error 00% 1856 - #13 Short offline Completed without error 00% 1855 - #14 Short offline Completed without error 00% 1855 - #15 Short offline Completed without error 00% 1855 - #16 Extended offline Aborted by host 70% 1855 - #17 Short offline Completed without error 00% 1855 - #18 Extended offline Completed without error 00% 1666 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 40/41 Celsius Lifetime Min/Max Temperature: 40/52 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (12) Index Estimated Time Temperature Celsius 13 2021-10-12 19:33 31 ************ 14 2021-10-12 19:34 31 ************ 15 2021-10-12 19:35 32 ************* 16 2021-10-12 19:36 32 ************* 17 2021-10-12 19:37 32 ************* 18 2021-10-12 19:38 ? - 19 2021-10-12 19:39 27 ******** 20 2021-10-12 19:40 27 ******** 21 2021-10-12 19:41 28 ********* 22 2021-10-12 19:42 30 *********** 23 2021-10-12 19:43 30 *********** 24 2021-10-12 19:44 30 *********** 25 2021-10-12 19:45 31 ************ 26 2021-10-12 19:46 31 ************ 27 2021-10-12 19:47 31 ************ 28 2021-10-12 19:48 32 ************* 29 2021-10-12 19:49 32 ************* 30 2021-10-12 19:50 32 ************* 31 2021-10-12 19:51 33 ************** 32 2021-10-12 19:52 33 ************** 33 2021-10-12 19:53 34 *************** ... ..( 3 skipped). .. *************** 37 2021-10-12 19:57 34 *************** 38 2021-10-12 19:58 35 **************** 39 2021-10-12 19:59 35 **************** 40 2021-10-12 20:00 35 **************** 41 2021-10-12 20:01 ? - 42 2021-10-12 20:02 34 *************** 43 2021-10-12 20:03 34 *************** 44 2021-10-12 20:04 35 **************** 45 2021-10-12 20:05 35 **************** 46 2021-10-12 20:06 36 ***************** 47 2021-10-12 20:07 36 ***************** 48 2021-10-12 20:08 37 ****************** ... ..( 2 skipped). .. ****************** 51 2021-10-12 20:11 37 ****************** 52 2021-10-12 20:12 38 ******************* ... ..( 5 skipped). .. ******************* 58 2021-10-12 20:18 38 ******************* 59 2021-10-12 20:19 39 ******************** 60 2021-10-12 20:20 38 ******************* 61 2021-10-12 20:21 39 ******************** ... ..( 12 skipped). .. ******************** 74 2021-10-12 20:34 39 ******************** 75 2021-10-12 20:35 40 ********************* ... ..( 15 skipped). .. ********************* 91 2021-10-12 20:51 40 ********************* 92 2021-10-12 20:52 41 ********************** 93 2021-10-12 20:53 41 ********************** 94 2021-10-12 20:54 40 ********************* 95 2021-10-12 20:55 41 ********************** ... ..( 8 skipped). .. ********************** 104 2021-10-12 21:04 41 ********************** 105 2021-10-12 21:05 42 *********************** ... ..( 10 skipped). .. *********************** 116 2021-10-12 21:16 42 *********************** 117 2021-10-12 21:17 41 ********************** 118 2021-10-12 21:18 41 ********************** 119 2021-10-12 21:19 41 ********************** 120 2021-10-12 21:20 42 *********************** 121 2021-10-12 21:21 41 ********************** 122 2021-10-12 21:22 42 *********************** 123 2021-10-12 21:23 42 *********************** 124 2021-10-12 21:24 41 ********************** ... ..( 5 skipped). .. ********************** 2 2021-10-12 21:30 41 ********************** 3 2021-10-12 21:31 40 ********************* 4 2021-10-12 21:32 ? - 5 2021-10-12 21:33 41 ********************** 6 2021-10-12 21:34 41 ********************** 7 2021-10-12 21:35 40 ********************* 8 2021-10-12 21:36 41 ********************** 9 2021-10-12 21:37 40 ********************* ... ..( 2 skipped). .. ********************* 12 2021-10-12 21:40 40 ********************* SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 451 Vendor specific