/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K80 Device Model: HDS728080PLAT20 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PF2OA2AA User Capacity: 82 348 277 760 bytes [82,3 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Fri Dec 28 22:20:58 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1828) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 31) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 108 108 024 - 169 (Average 198) 4 Start_Stop_Count -O--C- 100 100 000 - 3844 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 097 097 000 - 25344 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3784 192 Power-Off_Retract_Count -O--CK 097 097 050 - 3889 193 Load_Cycle_Count -O--C- 097 097 050 - 3889 194 Temperature_Celsius -O---- 152 152 000 - 36 (Min/Max 11/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST380815AS Serial Number: -- Firmware Version: 4.AAB User Capacity: 80 026 361 856 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Fri Dec 28 22:20:59 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3445 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 075 060 030 - 33230642 9 Power_On_Hours -O--CK 069 069 000 - 27573 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3238 187 Reported_Uncorrect -O--CK 001 001 000 - 133 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 052 045 - 37 (Min/Max 29/39) 194 Temperature_Celsius -O---K 037 048 000 - 37 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 078 065 000 - 130883982 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 136 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 136 [15] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:39.649 READ DMA EXT 25 00 ff 00 20 00 01 2a 00 8d 3f 40 00 00:49:39.625 READ DMA EXT 35 00 ff 00 08 00 01 2a 00 8d 17 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 20 00 04 09 00 a9 1f 40 00 00:49:36.212 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 7b 40 00 00:49:36.212 READ DMA EXT Error 135 [14] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:39.649 READ DMA EXT 25 00 ff 00 20 00 01 29 00 8d ff 40 00 00:49:39.625 READ DMA EXT 35 00 ff 00 08 00 01 29 00 8d df 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 08 00 01 29 00 8d 77 40 00 00:49:36.212 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 ff 40 00 00:49:36.212 WRITE DMA EXT Error 134 [13] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:29.278 READ DMA EXT 25 00 ff 00 20 00 01 29 00 8d 5f 40 00 00:49:29.255 READ DMA EXT 35 00 ff 00 08 00 01 28 00 8d 87 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 df 40 00 00:49:36.212 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 77 40 00 00:49:36.212 READ DMA EXT Error 133 [12] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:29.278 READ DMA EXT 25 00 ff 00 20 00 01 28 00 8d 7f 40 00 00:49:29.255 READ DMA EXT 35 00 ff 00 08 00 01 26 00 8d ff 40 00 00:49:25.851 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 bf 40 00 00:49:25.841 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 75 40 00 00:49:25.841 READ DMA EXT Error 132 [11] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:39.649 READ DMA EXT 25 00 ff 00 20 00 01 2a 00 8d 3f 40 00 00:49:39.625 READ DMA EXT 35 00 ff 00 08 00 01 2a 00 8d 17 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 20 00 04 09 00 a9 1f 40 00 00:49:36.212 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 7b 40 00 00:49:36.212 READ DMA EXT Error 131 [10] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:39.649 READ DMA EXT 25 00 ff 00 20 00 01 29 00 8d ff 40 00 00:49:39.625 READ DMA EXT 35 00 ff 00 08 00 01 29 00 8d df 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 08 00 01 29 00 8d 77 40 00 00:49:36.212 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 ff 40 00 00:49:36.212 WRITE DMA EXT Error 130 [9] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:29.278 READ DMA EXT 25 00 ff 00 20 00 01 29 00 8d 5f 40 00 00:49:29.255 READ DMA EXT 35 00 ff 00 08 00 01 28 00 8d 87 40 00 00:49:36.220 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 df 40 00 00:49:36.212 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 77 40 00 00:49:36.212 READ DMA EXT Error 129 [8] occurred at disk power-on lifetime: 27192 hours (1133 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e0 00 60 85 40 00 Error: UNC at LBA = 0xe0006085 = 3758121093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 e0 00 60 3f 40 00 00:49:29.278 READ DMA EXT 25 00 ff 00 20 00 01 28 00 8d 7f 40 00 00:49:29.255 READ DMA EXT 35 00 ff 00 08 00 01 26 00 8d ff 40 00 00:49:25.851 WRITE DMA EXT 35 00 ff 00 20 00 04 08 00 a9 bf 40 00 00:49:25.841 WRITE DMA EXT 25 00 ff 00 02 00 00 e0 00 60 75 40 00 00:49:25.841 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 106 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS