/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K500.B Device Model: Hitachi HTS545016B9A300 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PBBOC64G User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Feb 27 00:09:57 2021 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 65) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 109 109 040 - 4408 3 Spin_Up_Time POS--- 208 208 033 - 1 4 Start_Stop_Count -O--C- 097 097 000 - 4944 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 110 110 040 - 36 9 Power_On_Hours -O--C- 079 079 000 - 9594 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 3870 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 098 098 000 - 406 193 Load_Cycle_Count -O--C- 077 077 000 - 232655 194 Temperature_Celsius -O---- 211 211 000 - 26 (Min/Max 10/62) 196 Reallocated_Event_Count -O--CK 100 100 000 - 220 197 Current_Pending_Sector -O---K 100 100 000 - 52 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 4 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3448 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3448 [3] occurred at disk power-on lifetime: 6895 hours (287 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 a9 00 00 0a ba d4 30 ea 00 Error: UNC 169 sectors at LBA = 0x0abad430 = 180016176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 d8 00 00 0a ba d4 01 e0 00 00:08:01.800 READ DMA EXT 35 00 00 01 00 00 00 02 b8 cc 5f e0 00 00:08:01.400 WRITE DMA EXT 35 00 00 01 00 00 00 02 b8 cb 5f e0 00 00:08:01.400 WRITE DMA EXT 35 00 00 01 00 00 00 02 b8 ca 5f e0 00 00:08:01.400 WRITE DMA EXT 35 00 00 01 00 00 00 02 b8 c9 5f e0 00 00:08:01.400 WRITE DMA EXT Error 3447 [2] occurred at disk power-on lifetime: 6895 hours (287 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 a9 00 00 0a ba d4 30 ea 00 Error: UNC 169 sectors at LBA = 0x0abad430 = 180016176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 d8 00 00 0a ba d4 01 e0 00 00:07:55.600 READ DMA EXT 25 00 00 00 6a 00 00 0a ba d3 7f e0 00 00:07:55.500 READ DMA EXT 25 00 00 00 e6 00 00 09 ea b5 b9 e0 00 00:07:55.500 READ DMA EXT 25 00 00 00 e8 00 00 09 ea b3 d1 e0 00 00:07:55.500 READ DMA EXT 25 00 00 00 b2 00 00 09 ea b3 1f e0 00 00:07:55.500 READ DMA EXT Error 3446 [1] occurred at disk power-on lifetime: 6895 hours (287 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 39 00 00 0a ba d4 30 ea 00 Error: UNC 57 sectors at LBA = 0x0abad430 = 180016176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 0a ba d4 29 e0 00 00:01:22.900 READ DMA EXT 35 00 00 00 08 00 00 02 7c f5 2f e0 00 00:01:22.600 WRITE DMA EXT 35 00 00 00 08 00 00 02 7c 08 4f e0 00 00:01:22.600 WRITE DMA EXT 35 00 00 00 10 00 00 02 7c 07 97 e0 00 00:01:22.600 WRITE DMA EXT 35 00 00 00 08 00 00 00 61 e9 cf e0 00 00:01:22.600 WRITE DMA EXT Error 3445 [0] occurred at disk power-on lifetime: 6895 hours (287 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 3f 00 00 0a ba d4 30 ea 00 Error: UNC 63 sectors at LBA = 0x0abad430 = 180016176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 0a ba d4 27 e0 00 00:01:01.000 READ DMA EXT 35 00 00 00 08 00 00 09 50 a7 1f e0 00 00:01:01.000 WRITE DMA EXT 35 00 00 00 08 00 00 02 80 7a 47 e0 00 00:01:01.000 WRITE DMA EXT 25 00 00 00 10 00 00 0a ba d3 7f e0 00 00:01:00.900 READ DMA EXT 25 00 00 00 40 00 00 0a a2 8b d7 e0 00 00:01:00.900 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 21/26 Celsius Lifetime Min/Max Temperature: 10/62 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 478 (331) Index Estimated Time Temperature Celsius 332 2021-02-26 16:12 28 ********* ... ..( 15 skipped). .. ********* 348 2021-02-26 16:28 28 ********* 349 2021-02-26 16:29 29 ********** ... ..(109 skipped). .. ********** 459 2021-02-26 18:19 29 ********** 460 2021-02-26 18:20 30 *********** 461 2021-02-26 18:21 30 *********** 462 2021-02-26 18:22 31 ************ ... ..( 14 skipped). .. ************ 477 2021-02-26 18:37 31 ************ 0 2021-02-26 18:38 30 *********** ... ..( 31 skipped). .. *********** 32 2021-02-26 19:10 30 *********** 33 2021-02-26 19:11 29 ********** ... ..( 15 skipped). .. ********** 49 2021-02-26 19:27 29 ********** 50 2021-02-26 19:28 30 *********** 51 2021-02-26 19:29 29 ********** ... ..( 71 skipped). .. ********** 123 2021-02-26 20:41 29 ********** 124 2021-02-26 20:42 30 *********** ... ..( 57 skipped). .. *********** 182 2021-02-26 21:40 30 *********** 183 2021-02-26 21:41 31 ************ ... ..( 4 skipped). .. ************ 188 2021-02-26 21:46 31 ************ 189 2021-02-26 21:47 32 ************* ... ..( 9 skipped). .. ************* 199 2021-02-26 21:57 32 ************* 200 2021-02-26 21:58 31 ************ ... ..( 4 skipped). .. ************ 205 2021-02-26 22:03 31 ************ 206 2021-02-26 22:04 30 *********** ... ..( 10 skipped). .. *********** 217 2021-02-26 22:15 30 *********** 218 2021-02-26 22:16 29 ********** 219 2021-02-26 22:17 30 *********** 220 2021-02-26 22:18 29 ********** ... ..( 11 skipped). .. ********** 232 2021-02-26 22:30 29 ********** 233 2021-02-26 22:31 30 *********** 234 2021-02-26 22:32 30 *********** 235 2021-02-26 22:33 29 ********** ... ..( 6 skipped). .. ********** 242 2021-02-26 22:40 29 ********** 243 2021-02-26 22:41 28 ********* 244 2021-02-26 22:42 29 ********** ... ..( 36 skipped). .. ********** 281 2021-02-26 23:19 29 ********** 282 2021-02-26 23:20 30 *********** ... ..( 5 skipped). .. *********** 288 2021-02-26 23:26 30 *********** 289 2021-02-26 23:27 31 ************ ... ..( 14 skipped). .. ************ 304 2021-02-26 23:42 31 ************ 305 2021-02-26 23:43 32 ************* ... ..( 9 skipped). .. ************* 315 2021-02-26 23:53 32 ************* 316 2021-02-26 23:54 21 ** 317 2021-02-26 23:55 22 *** 318 2021-02-26 23:56 22 *** 319 2021-02-26 23:57 22 *** 320 2021-02-26 23:58 23 **** 321 2021-02-26 23:59 23 **** 322 2021-02-27 00:00 23 **** 323 2021-02-27 00:01 24 ***** 324 2021-02-27 00:02 24 ***** 325 2021-02-27 00:03 24 ***** 326 2021-02-27 00:04 25 ****** 327 2021-02-27 00:05 25 ****** 328 2021-02-27 00:06 25 ****** 329 2021-02-27 00:07 26 ******* 330 2021-02-27 00:08 26 ******* 331 2021-02-27 00:09 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS