/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.3.0-51-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10JPVX-22JC3T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 17 14:28:46 2020 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (19560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 218) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 6 3 Spin_Up_Time POS--K 183 178 021 - 1833 4 Start_Stop_Count -O--CK 044 044 000 - 56404 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7620 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4559 191 G-Sense_Error_Rate -O--CK 001 001 000 - 146 192 Power-Off_Retract_Count -O--CK 200 200 000 - 133 193 Load_Cycle_Count -O--CK 156 156 000 - 132207 194 Temperature_Celsius -O---K 109 093 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 2506 hours (104 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 23 cc f8 e0 00 Error: UNC 128 sectors at LBA = 0x0323ccf8 = 52677880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:20.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:17.284 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc 40 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cb c0 e0 00 00:00:13.954 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 2506 hours (104 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 23 cc f8 e0 00 Error: UNC 128 sectors at LBA = 0x0323ccf8 = 52677880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:17.284 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc 40 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cb c0 e0 00 00:00:13.954 READ DMA EXT 25 00 00 00 80 00 00 03 23 cb 40 e0 00 00:00:13.954 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 2506 hours (104 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 23 cc f8 e0 00 Error: UNC 128 sectors at LBA = 0x0323ccf8 = 52677880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 23 cc c0 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cc 40 e0 00 00:00:13.955 READ DMA EXT 25 00 00 00 80 00 00 03 23 cb c0 e0 00 00:00:13.954 READ DMA EXT 25 00 00 00 80 00 00 03 23 cb 40 e0 00 00:00:13.954 READ DMA EXT 25 00 00 00 80 00 00 03 23 ca c0 e0 00 00:00:13.953 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 824 hours (34 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 0d a5 48 e0 00 Error: UNC 128 sectors at LBA = 0x030da548 = 51225928 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:12.672 READ DMA EXT 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:08.888 READ DMA EXT 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:05.294 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 c0 e0 00 00:00:05.293 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 40 e0 00 00:00:05.293 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 824 hours (34 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 0d a5 48 e0 00 Error: UNC 128 sectors at LBA = 0x030da548 = 51225928 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:08.888 READ DMA EXT 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:05.294 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 c0 e0 00 00:00:05.293 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 40 e0 00 00:00:05.293 READ DMA EXT 25 00 00 00 80 00 00 03 0d a3 c0 e0 00 00:00:05.292 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 824 hours (34 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 03 0d a5 48 e0 00 Error: UNC 128 sectors at LBA = 0x030da548 = 51225928 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 03 0d a5 40 e0 00 00:00:05.294 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 c0 e0 00 00:00:05.293 READ DMA EXT 25 00 00 00 80 00 00 03 0d a4 40 e0 00 00:00:05.293 READ DMA EXT 25 00 00 00 80 00 00 03 0d a3 c0 e0 00 00:00:05.292 READ DMA EXT 25 00 00 00 80 00 00 03 0d a3 40 e0 00 00:00:05.292 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 33/38 Celsius Lifetime Min/Max Temperature: 6/54 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (103) Index Estimated Time Temperature Celsius 104 2020-05-17 12:21 33 ************** ... ..( 3 skipped). .. ************** 108 2020-05-17 12:25 33 ************** 109 2020-05-17 12:26 34 *************** ... ..( 5 skipped). .. *************** 115 2020-05-17 12:32 34 *************** 116 2020-05-17 12:33 35 **************** 117 2020-05-17 12:34 35 **************** 118 2020-05-17 12:35 35 **************** 119 2020-05-17 12:36 36 ***************** ... ..( 36 skipped). .. ***************** 28 2020-05-17 13:13 36 ***************** 29 2020-05-17 13:14 ? - 30 2020-05-17 13:15 31 ************ 31 2020-05-17 13:16 31 ************ 32 2020-05-17 13:17 31 ************ 33 2020-05-17 13:18 32 ************* 34 2020-05-17 13:19 32 ************* 35 2020-05-17 13:20 33 ************** 36 2020-05-17 13:21 33 ************** 37 2020-05-17 13:22 ? - 38 2020-05-17 13:23 33 ************** 39 2020-05-17 13:24 33 ************** 40 2020-05-17 13:25 34 *************** 41 2020-05-17 13:26 34 *************** 42 2020-05-17 13:27 35 **************** 43 2020-05-17 13:28 35 **************** 44 2020-05-17 13:29 35 **************** 45 2020-05-17 13:30 36 ***************** ... ..( 20 skipped). .. ***************** 66 2020-05-17 13:51 36 ***************** 67 2020-05-17 13:52 37 ****************** 68 2020-05-17 13:53 37 ****************** 69 2020-05-17 13:54 37 ****************** 70 2020-05-17 13:55 36 ***************** ... ..( 12 skipped). .. ***************** 83 2020-05-17 14:08 36 ***************** 84 2020-05-17 14:09 37 ****************** ... ..( 8 skipped). .. ****************** 93 2020-05-17 14:18 37 ****************** 94 2020-05-17 14:19 38 ******************* 95 2020-05-17 14:20 37 ****************** 96 2020-05-17 14:21 38 ******************* ... ..( 6 skipped). .. ******************* 103 2020-05-17 14:28 38 ******************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 3968 Vendor specific