/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-137-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9500325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0004SDM2 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Sat May 6 22:08:11 2023 EAT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 142) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 083 006 - 213258262 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 075 075 020 - 26471 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 33 7 Seek_Error_Rate POSR-- 081 060 030 - 39901211280 9 Power_On_Hours -O--CK 062 062 000 - 33436 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 088 037 020 - 12479 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 5638 188 Command_Timeout -O--CK 100 099 000 - 25770197006 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 054 036 045 Past 46 (Min/Max 46/47 #4440) 191 G-Sense_Error_Rate -O--CK 096 096 000 - 8391 192 Power-Off_Retract_Count -O--CK 100 100 000 - 882 193 Load_Cycle_Count -O--CK 001 001 000 - 262089 194 Temperature_Celsius -O---K 046 064 000 - 46 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 048 040 000 - 213258262 197 Current_Pending_Sector -O--C- 100 100 000 - 5 198 Offline_Uncorrectable ----C- 100 100 000 - 5 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 6840 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6840 [19] occurred at disk power-on lifetime: 32388 hours (1349 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 60 3f 76 00 00 Error: WP at LBA = 0x29603f76 = 694173558 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 10 00 00 0c 2f 54 80 40 00 02:08:55.525 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 29 60 3f 70 40 00 02:08:55.525 READ FPDMA QUEUED 60 00 00 01 00 00 00 11 8a ad 18 40 00 02:08:55.523 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:08:55.503 FLUSH CACHE EXT 60 00 00 00 88 00 00 13 30 ce 10 40 00 02:08:55.474 READ FPDMA QUEUED Error 6839 [18] occurred at disk power-on lifetime: 32388 hours (1349 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 60 3f 76 00 00 Error: UNC at LBA = 0x29603f76 = 694173558 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 60 3f 70 40 00 02:08:52.871 READ FPDMA QUEUED 60 00 00 00 b8 00 00 03 a0 ad 80 40 00 02:08:52.870 READ FPDMA QUEUED 61 00 00 00 08 00 00 0c 2f 53 a8 40 00 02:08:52.870 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:08:52.841 FLUSH CACHE EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:08:52.841 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 6838 [17] occurred at disk power-on lifetime: 32388 hours (1349 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 60 3f 76 00 00 Error: UNC at LBA = 0x29603f76 = 694173558 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 29 60 3f 70 40 00 02:08:50.414 READ FPDMA QUEUED 61 00 00 01 50 00 00 0c 2f 52 58 40 00 02:08:50.414 WRITE FPDMA QUEUED 60 00 00 00 80 00 00 11 8a a8 30 40 00 02:08:50.413 READ FPDMA QUEUED 60 00 00 00 10 00 00 11 8a a8 00 40 00 02:08:50.413 READ FPDMA QUEUED 60 00 00 00 48 00 00 04 1c 27 a8 40 00 02:08:50.412 READ FPDMA QUEUED Error 6837 [16] occurred at disk power-on lifetime: 32388 hours (1349 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 60 3f 76 00 00 Error: UNC at LBA = 0x29603f76 = 694173558 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 29 60 3e c8 40 00 02:08:46.973 READ FPDMA QUEUED 60 00 00 01 00 00 00 07 97 b6 10 40 00 02:08:46.924 READ FPDMA QUEUED 60 00 00 00 98 00 00 07 97 b5 78 40 00 02:08:46.905 READ FPDMA QUEUED 60 00 00 00 08 00 00 07 97 b5 50 40 00 02:08:46.904 READ FPDMA QUEUED 60 00 00 00 38 00 00 07 97 b5 10 40 00 02:08:46.903 READ FPDMA QUEUED Error 6836 [15] occurred at disk power-on lifetime: 29171 hours (1215 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 6b 77 c7 00 00 Error: UNC at LBA = 0x006b77c7 = 7043015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 6b 77 c7 40 00 00:55:41.071 READ FPDMA QUEUED 60 00 00 00 20 00 00 00 5d 17 01 40 00 00:55:41.046 READ FPDMA QUEUED 60 00 00 00 08 00 00 01 a7 a4 a0 40 00 00:55:41.034 READ FPDMA QUEUED 60 00 00 00 18 00 00 00 72 99 9a 40 00 00:55:41.018 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 32 1c 92 40 00 00:55:41.017 READ FPDMA QUEUED Error 6835 [14] occurred at disk power-on lifetime: 29171 hours (1215 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 6b 77 c7 00 00 Error: UNC at LBA = 0x006b77c7 = 7043015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 00 5d 17 01 40 00 00:55:38.439 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 6b 77 c7 40 00 00:55:38.439 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 5d 13 81 40 00 00:55:38.426 READ FPDMA QUEUED 60 00 00 00 20 00 00 00 32 1c 5a 40 00 00:55:38.411 READ FPDMA QUEUED 60 00 00 00 05 00 00 01 39 b5 f0 40 00 00:55:38.396 READ FPDMA QUEUED Error 6834 [13] occurred at disk power-on lifetime: 29171 hours (1215 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 6b 77 c7 00 00 Error: UNC at LBA = 0x006b77c7 = 7043015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5d 13 81 40 00 00:55:35.816 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 6b 77 c7 40 00 00:55:35.815 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 4e af f4 40 00 00:55:35.806 READ FPDMA QUEUED 60 00 00 00 10 00 00 00 32 1c 12 40 00 00:55:35.799 READ FPDMA QUEUED 60 00 00 00 0f 00 00 00 6f 6f 3a 40 00 00:55:35.766 READ FPDMA QUEUED Error 6833 [12] occurred at disk power-on lifetime: 29171 hours (1215 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 6b 77 c7 00 00 Error: UNC at LBA = 0x006b77c7 = 7043015 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 4e af f4 40 00 00:55:33.236 READ FPDMA QUEUED 60 00 00 00 40 00 00 00 5d 89 b7 40 00 00:55:33.230 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 6b 77 c7 40 00 00:55:33.230 READ FPDMA QUEUED 60 00 00 00 08 00 00 14 ab 64 f0 40 00 00:55:33.218 READ FPDMA QUEUED 60 00 00 00 18 00 00 00 5d 86 af 40 00 00:55:33.205 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 46 Celsius Power Cycle Min/Max Temperature: 46/47 Celsius Lifetime Min/Max Temperature: 14/64 Celsius Under/Over Temperature Limit Count: 0/17 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2023-05-06 20:01 45 ************************** ... ..( 78 skipped). .. ************************** 81 2023-05-06 21:20 45 ************************** 82 2023-05-06 21:21 46 *************************** ... ..( 17 skipped). .. *************************** 100 2023-05-06 21:39 46 *************************** 101 2023-05-06 21:40 47 **************************** 102 2023-05-06 21:41 47 **************************** 103 2023-05-06 21:42 47 **************************** 104 2023-05-06 21:43 46 *************************** 105 2023-05-06 21:44 47 **************************** 106 2023-05-06 21:45 47 **************************** 107 2023-05-06 21:46 46 *************************** ... ..( 3 skipped). .. *************************** 111 2023-05-06 21:50 46 *************************** 112 2023-05-06 21:51 ? - 113 2023-05-06 21:52 46 *************************** ... ..( 3 skipped). .. *************************** 117 2023-05-06 21:56 46 *************************** 118 2023-05-06 21:57 47 **************************** ... ..( 6 skipped). .. **************************** 125 2023-05-06 22:04 47 **************************** 126 2023-05-06 22:05 46 *************************** ... ..( 2 skipped). .. *************************** 1 2023-05-06 22:08 46 *************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS