/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.2-1-MANJARO] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10JPVX-22JC3T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Feb 8 23:42:46 2020 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17640) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 198) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 10 3 Spin_Up_Time POS--K 183 180 021 - 1841 4 Start_Stop_Count -O--CK 087 087 000 - 13602 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 088 088 000 - 9005 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6186 191 G-Sense_Error_Rate -O--CK 043 043 000 - 57 192 Power-Off_Retract_Count -O--CK 200 200 000 - 255 193 Load_Cycle_Count -O--CK 188 188 000 - 37485 194 Temperature_Celsius -O---K 108 094 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a0 00 00 00 75 7a b8 40 00 00:00:47.497 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:46.529 SET FEATURES [Enable write cache] 60 00 08 00 98 00 00 00 75 7a b8 40 00 00:00:42.986 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:42.018 SET FEATURES [Enable write cache] 60 00 08 00 90 00 00 00 75 7a b8 40 00 00:00:38.381 READ FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 00 75 7a b8 40 00 00:00:42.986 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:42.018 SET FEATURES [Enable write cache] 60 00 08 00 90 00 00 00 75 7a b8 40 00 00:00:38.381 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:37.445 SET FEATURES [Enable write cache] 60 00 08 00 88 00 00 00 75 7a b8 40 00 00:00:33.870 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 90 00 00 00 75 7a b8 40 00 00:00:38.381 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:37.445 SET FEATURES [Enable write cache] 60 00 08 00 88 00 00 00 75 7a b8 40 00 00:00:33.870 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:33.183 SET FEATURES [Enable write cache] 60 00 08 00 80 00 00 00 75 7a b8 40 00 00:00:29.413 READ FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 00 75 7a b8 40 00 00:00:33.870 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:33.183 SET FEATURES [Enable write cache] 60 00 08 00 80 00 00 00 75 7a b8 40 00 00:00:29.413 READ FPDMA QUEUED 61 00 08 00 78 00 00 00 75 7a b0 40 00 00:00:29.412 WRITE FPDMA QUEUED 61 00 08 00 70 00 00 00 75 7a a8 40 00 00:00:29.412 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 00 75 7a b8 40 00 00:00:29.413 READ FPDMA QUEUED 61 00 08 00 78 00 00 00 75 7a b0 40 00 00:00:29.412 WRITE FPDMA QUEUED 61 00 08 00 70 00 00 00 75 7a a8 40 00 00:00:29.412 WRITE FPDMA QUEUED 61 00 08 00 68 00 00 00 75 7a a0 40 00 00:00:29.412 WRITE FPDMA QUEUED 61 00 08 00 60 00 00 00 75 7a 98 40 00 00:00:29.412 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 00 75 7a b8 40 00 00:00:25.784 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:24.848 SET FEATURES [Enable write cache] 60 00 08 00 e8 00 00 00 75 7a b8 40 00 00:00:21.273 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:20.305 SET FEATURES [Enable write cache] 60 00 08 00 e0 00 00 00 75 7a b8 40 00 00:00:16.762 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e8 00 00 00 75 7a b8 40 00 00:00:21.273 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:20.305 SET FEATURES [Enable write cache] 60 00 08 00 e0 00 00 00 75 7a b8 40 00 00:00:16.762 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:15.825 SET FEATURES [Enable write cache] 60 00 08 00 d8 00 00 00 75 7a b8 40 00 00:00:12.266 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 838 hours (34 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 75 7a b8 40 00 Error: UNC at LBA = 0x00757ab8 = 7699128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e0 00 00 00 75 7a b8 40 00 00:00:16.762 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:15.825 SET FEATURES [Enable write cache] 60 00 08 00 d8 00 00 00 75 7a b8 40 00 00:00:12.266 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:00:11.611 SET FEATURES [Enable write cache] 60 00 08 00 d0 00 00 00 75 7a b8 40 00 00:00:07.702 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7036 - # 2 Short offline Completed without error 00% 5486 - # 3 Extended offline Interrupted (host reset) 80% 5429 - # 4 Short offline Completed without error 00% 5428 - # 5 Extended offline Aborted by host 90% 4291 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 30/41 Celsius Lifetime Min/Max Temperature: 13/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (97) Index Estimated Time Temperature Celsius 98 2020-02-08 21:35 40 ********************* ... ..( 14 skipped). .. ********************* 113 2020-02-08 21:50 40 ********************* 114 2020-02-08 21:51 39 ******************** ... ..( 26 skipped). .. ******************** 13 2020-02-08 22:18 39 ******************** 14 2020-02-08 22:19 38 ******************* ... ..( 15 skipped). .. ******************* 30 2020-02-08 22:35 38 ******************* 31 2020-02-08 22:36 39 ******************** ... ..( 65 skipped). .. ******************** 97 2020-02-08 23:42 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 44913 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 14682 Vendor specific