/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-80-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SUNEAST SSD SE800 1TB Serial Number: -- Firmware Version: S0424A0 User Capacity: 1,024,209,543,168 bytes [1.02 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Aug 23 19:08:24 2021 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 4946 12 Power_Cycle_Count -O--CK 100 100 050 - 61 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 12 164 Unknown_Attribute -O--CK 100 100 050 - 1545 165 Unknown_Attribute -O--CK 100 100 050 - 6 166 Unknown_Attribute -O--CK 100 100 050 - 1 167 Unknown_Attribute -O--CK 100 100 050 - 2 168 Unknown_Attribute -O--CK 100 100 050 - 7000 169 Unknown_Attribute -O--CK 100 100 050 - 100 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 35 194 Temperature_Celsius -O---K 100 100 050 - 39 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 30511 242 Total_LBAs_Read ----CK 100 100 050 - 6190 245 Unknown_Attribute -O--CK 100 100 050 - 9639 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 61 --- Lifetime Power-On Resets 0x01 0x010 4 4946 --- Power-on Hours 0x01 0x018 6 1999601873 --- Logical Sectors Written 0x01 0x020 6 1261204 --- Number of Write Commands 0x01 0x028 6 405688456 --- Logical Sectors Read 0x01 0x030 6 347324 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 2 R_ERR response for non-data FIS 0x000a 4 7 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-80-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD10JMVW-11AJGS4 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Aug 23 19:08:24 2021 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17940) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 201) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 198 051 - 2550 3 Spin_Up_Time POS--K 131 125 021 - 4433 4 Start_Stop_Count -O--CK 097 097 000 - 3726 5 Reallocated_Sector_Ct PO--CK 185 185 140 - 672 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 070 070 000 - 22556 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 628 192 Power-Off_Retract_Count -O--CK 200 200 000 - 154 193 Load_Cycle_Count -O--CK 186 186 000 - 43353 194 Temperature_Celsius -O---K 116 096 000 - 31 196 Reallocated_Event_Count -O--CK 183 183 000 - 17 197 Current_Pending_Sector -O--CK 200 200 000 - 3 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1743 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1743 [14] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:41.731 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:38.236 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:34.719 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:31.212 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:27.872 READ DMA EXT Error 1742 [13] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:38.236 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:34.719 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:31.212 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:27.872 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 38 40 00 00:02:27.871 READ DMA EXT Error 1741 [12] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:34.719 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:31.212 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:27.872 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 38 40 00 00:02:27.871 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 30 40 00 00:02:27.871 READ DMA EXT Error 1740 [11] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:31.212 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:27.872 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 38 40 00 00:02:27.871 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 30 40 00 00:02:27.871 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 28 40 00 00:02:27.870 READ DMA EXT Error 1739 [10] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:02:27.872 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 38 40 00 00:02:27.871 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 30 40 00 00:02:27.871 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 28 40 00 00:02:27.870 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 20 40 00 00:02:27.869 READ DMA EXT Error 1738 [9] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 f0 00 00 01 38 f3 40 40 00 Error: UNC 240 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 f0 00 00 01 38 f3 00 40 00 00:02:24.312 READ DMA EXT 25 00 00 00 10 00 00 01 38 f2 f0 40 00 00:02:24.311 READ DMA EXT 25 00 00 00 f0 00 00 01 38 f2 00 40 00 00:02:24.308 READ DMA EXT 25 00 00 00 10 00 00 01 38 f1 f0 40 00 00:02:24.307 READ DMA EXT 25 00 00 00 f0 00 00 01 38 f1 00 40 00 00:02:24.303 READ DMA EXT Error 1737 [8] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:12.729 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:09.233 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:05.738 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:02.156 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:00:58.793 READ DMA EXT Error 1736 [7] occurred at disk power-on lifetime: 17661 hours (735 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 01 38 f3 40 40 00 Error: UNC 8 sectors at LBA = 0x0138f340 = 20509504 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:09.233 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:05.738 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:01:02.156 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 40 40 00 00:00:58.793 READ DMA EXT 25 00 00 00 08 00 00 01 38 f3 38 40 00 00:00:58.792 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 17/34 Celsius Lifetime Min/Max Temperature: -3/51 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (58) Index Estimated Time Temperature Celsius 59 2021-08-23 17:01 28 ********* ... ..(107 skipped). .. ********* 39 2021-08-23 18:49 28 ********* 40 2021-08-23 18:50 ? - 41 2021-08-23 18:51 28 ********* 42 2021-08-23 18:52 28 ********* 43 2021-08-23 18:53 28 ********* 44 2021-08-23 18:54 29 ********** ... ..( 2 skipped). .. ********** 47 2021-08-23 18:57 29 ********** 48 2021-08-23 18:58 30 *********** ... ..( 2 skipped). .. *********** 51 2021-08-23 19:01 30 *********** 52 2021-08-23 19:02 31 ************ ... ..( 5 skipped). .. ************ 58 2021-08-23 19:08 31 ************ SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 850595 Vendor specific