/dev/sda,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: 734F59FFC4CB5E90EE8BF2F9B95B883E LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:22 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 097 097 010 - 82 9 Power_On_Hours -O--CK 089 089 000 - 52075 12 Power_Cycle_Count -O--CK 099 099 000 - 29 177 Wear_Leveling_Count PO--C- 089 089 005 - 811 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 097 097 010 - 82 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 097 097 010 - 3187 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 097 097 010 - 82 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 1697 190 Airflow_Temperature_Cel -O--CK 059 046 000 - 41 194 Temperature_Celsius -O---K 059 046 000 - 41 (Min/Max 15/54) 195 ECC_Error_Rate -O-RC- 199 199 000 - 1697 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 23 241 Total_LBAs_Written -O--CK 099 099 000 - 820416154367 242 Total_LBAs_Read -O--CK 099 099 000 - 2689724507149 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1735734298624 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1697 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1697 [0] occurred at disk power-on lifetime: 37285 hours (1553 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 49 d5 1a c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 19 c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 00 80 00 00 00 00 49 d5 18 40 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 00 40 00 00 00 00 49 d5 18 00 00 00 38d+00:11:10.448 READ FPDMA QUEUED Error 1696 [3] occurred at disk power-on lifetime: 37266 hours (1552 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 49 d5 1a b0 00 00 37d+05:27:12.448 READ FPDMA QUEUED 60 00 50 00 00 00 00 49 d5 19 b0 00 00 37d+05:27:12.448 READ FPDMA QUEUED 60 00 40 00 10 00 00 09 10 ad 20 00 02 37d+05:27:12.448 READ FPDMA QUEUED 60 00 60 00 08 00 00 09 0d 3e 40 00 01 37d+05:27:12.448 READ FPDMA QUEUED 60 00 60 00 00 00 00 09 0c e1 28 00 00 37d+05:27:12.448 READ FPDMA QUEUED Error 1695 [2] occurred at disk power-on lifetime: 37209 hours (1550 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 49 d5 1a 80 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 19 00 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 00 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 00 10 00 00 00 00 21 81 ea 58 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 00 10 00 00 00 00 21 81 ea 28 00 00 34d+20:23:14.448 READ FPDMA QUEUED Error 1694 [1] occurred at disk power-on lifetime: 37182 hours (1549 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 49 d5 1a 80 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 e0 00 00 00 00 49 d5 19 00 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 00 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 20 00 00 00 00 69 9d e5 40 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 70 00 00 00 00 1f 60 3f 50 00 00 33d+17:15:17.448 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 33/54 Celsius Lifetime Min/Max Temperature: 15/54 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 29 --- Lifetime Power-On Resets 0x01 0x010 4 52075 --- Power-on Hours 0x01 0x018 6 820416154367 --- Logical Sectors Written 0x01 0x020 6 5835086803 --- Number of Write Commands 0x01 0x028 6 2689724507149 --- Logical Sectors Read 0x01 0x030 6 20245136472 --- Number of Read Commands 0x01 0x038 6 2855000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1697 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 62 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: 734F59FFC4CB5E90EE8BF2F9B95B883E LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 097 097 010 - 82 9 Power_On_Hours -O--CK 089 089 000 - 52075 12 Power_Cycle_Count -O--CK 099 099 000 - 29 177 Wear_Leveling_Count PO--C- 089 089 005 - 811 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 097 097 010 - 82 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 097 097 010 - 3187 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 097 097 010 - 82 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 1697 190 Airflow_Temperature_Cel -O--CK 059 046 000 - 41 194 Temperature_Celsius -O---K 059 046 000 - 41 (Min/Max 15/54) 195 ECC_Error_Rate -O-RC- 199 199 000 - 1697 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 23 241 Total_LBAs_Written -O--CK 099 099 000 - 820416154367 242 Total_LBAs_Read -O--CK 099 099 000 - 2689724507829 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1735734298624 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1697 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1697 [0] occurred at disk power-on lifetime: 37285 hours (1553 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 49 d5 1a c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 19 c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 c0 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 00 80 00 00 00 00 49 d5 18 40 00 00 38d+00:11:10.448 READ FPDMA QUEUED 60 00 40 00 00 00 00 49 d5 18 00 00 00 38d+00:11:10.448 READ FPDMA QUEUED Error 1696 [3] occurred at disk power-on lifetime: 37266 hours (1552 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 49 d5 1a b0 00 00 37d+05:27:12.448 READ FPDMA QUEUED 60 00 50 00 00 00 00 49 d5 19 b0 00 00 37d+05:27:12.448 READ FPDMA QUEUED 60 00 40 00 10 00 00 09 10 ad 20 00 02 37d+05:27:12.448 READ FPDMA QUEUED 60 00 60 00 08 00 00 09 0d 3e 40 00 01 37d+05:27:12.448 READ FPDMA QUEUED 60 00 60 00 00 00 00 09 0c e1 28 00 00 37d+05:27:12.448 READ FPDMA QUEUED Error 1695 [2] occurred at disk power-on lifetime: 37209 hours (1550 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 49 d5 1a 80 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 19 00 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 00 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 00 10 00 00 00 00 21 81 ea 58 00 00 34d+20:23:14.448 READ FPDMA QUEUED 60 00 10 00 00 00 00 21 81 ea 28 00 00 34d+20:23:14.448 READ FPDMA QUEUED Error 1694 [1] occurred at disk power-on lifetime: 37182 hours (1549 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 49 d5 1a 80 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 e0 00 00 00 00 49 d5 19 00 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 01 00 00 00 00 00 49 d5 18 00 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 20 00 00 00 00 69 9d e5 40 00 00 33d+17:15:17.448 READ FPDMA QUEUED 60 00 70 00 00 00 00 1f 60 3f 50 00 00 33d+17:15:17.448 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 33/54 Celsius Lifetime Min/Max Temperature: 15/54 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 29 --- Lifetime Power-On Resets 0x01 0x010 4 52075 --- Power-on Hours 0x01 0x018 6 820416154367 --- Logical Sectors Written 0x01 0x020 6 5835086803 --- Number of Write Commands 0x01 0x028 6 2689724507829 --- Logical Sectors Read 0x01 0x030 6 20245136508 --- Number of Read Commands 0x01 0x038 6 2855000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1697 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 62 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: AB62E45E06F76EB2C01FBE12BA305248 LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 098 098 010 - 66 9 Power_On_Hours -O--CK 090 090 000 - 50379 12 Power_Cycle_Count -O--CK 099 099 000 - 53 177 Wear_Leveling_Count PO--C- 090 090 005 - 676 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 66 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 3214 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 098 098 010 - 66 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 596 190 Airflow_Temperature_Cel -O--CK 059 047 000 - 41 194 Temperature_Celsius -O---K 059 047 000 - 41 (Min/Max 15/53) 195 ECC_Error_Rate -O-RC- 199 199 000 - 596 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 3 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 47 241 Total_LBAs_Written -O--CK 099 099 000 - 785238087863 242 Total_LBAs_Read -O--CK 099 099 000 - 2570177911476 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1446667475968 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 596 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 596 [3] occurred at disk power-on lifetime: 35409 hours (1475 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 25 21 d8 20 00 00 9d+00:35:54.000 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d7 20 00 00 9d+00:35:54.000 READ FPDMA QUEUED 60 01 00 00 00 00 00 15 04 74 b0 00 00 9d+00:35:54.000 READ FPDMA QUEUED 60 00 e8 00 08 00 00 15 04 73 c8 00 01 9d+00:35:54.000 READ FPDMA QUEUED 60 00 18 00 00 00 00 1b 1d 97 e8 00 00 9d+00:35:54.000 READ FPDMA QUEUED Error 595 [2] occurred at disk power-on lifetime: 34085 hours (1420 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 25 21 d8 20 00 00 11d+09:29:39.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d7 20 00 00 11d+09:29:39.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d6 20 00 00 11d+09:29:39.408 READ FPDMA QUEUED 60 00 20 00 08 00 00 25 21 d6 00 00 01 11d+09:29:39.408 READ FPDMA QUEUED 60 00 e0 00 00 00 00 25 1b 15 98 00 00 11d+09:29:39.408 READ FPDMA QUEUED Error 594 [1] occurred at disk power-on lifetime: 34078 hours (1419 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 25 21 d8 20 00 00 11d+02:12:39.408 READ FPDMA QUEUED 60 00 08 00 00 00 00 32 81 11 40 00 00 11d+02:12:39.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d7 20 00 00 11d+02:12:39.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d6 20 00 00 11d+02:12:39.408 READ FPDMA QUEUED 60 00 20 00 08 00 00 25 21 d6 00 00 01 11d+02:12:39.408 READ FPDMA QUEUED Error 593 [0] occurred at disk power-on lifetime: 34076 hours (1419 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 25 21 d8 20 00 00 11d+00:16:29.408 READ FPDMA QUEUED 60 00 18 00 00 00 00 26 f8 1c 08 00 00 11d+00:16:29.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d7 20 00 00 11d+00:16:29.408 READ FPDMA QUEUED 60 01 00 00 00 00 00 25 21 d6 20 00 00 11d+00:16:29.408 READ FPDMA QUEUED 60 00 20 00 08 00 00 25 21 d6 00 00 01 11d+00:16:29.408 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 33/53 Celsius Lifetime Min/Max Temperature: 15/53 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 53 --- Lifetime Power-On Resets 0x01 0x010 4 50379 --- Power-on Hours 0x01 0x018 6 785238087863 --- Logical Sectors Written 0x01 0x020 6 5578951906 --- Number of Write Commands 0x01 0x028 6 2570177911476 --- Logical Sectors Read 0x01 0x030 6 19386557046 --- Number of Read Commands 0x01 0x038 6 2738000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 596 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 6 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x020 1 53 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 68 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 3 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 9 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: 147EDB40F919515411EB1A32ED9F157C LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 098 098 010 - 54 9 Power_On_Hours -O--CK 089 089 000 - 52247 12 Power_Cycle_Count -O--CK 099 099 000 - 35 177 Wear_Leveling_Count PO--C- 088 088 005 - 831 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 54 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 3198 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 098 098 010 - 54 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 291 190 Airflow_Temperature_Cel -O--CK 060 048 000 - 40 194 Temperature_Celsius -O---K 060 048 000 - 40 (Min/Max 14/52) 195 ECC_Error_Rate -O-RC- 199 199 000 - 291 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 30 241 Total_LBAs_Written -O--CK 099 099 000 - 840297116362 242 Total_LBAs_Read -O--CK 098 098 000 - 2876471126464 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1777015595008 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 291 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 291 [2] occurred at disk power-on lifetime: 41019 hours (1709 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 42 81 cb f8 00 00 25d+03:29:08.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 42 81 ca f8 00 00 25d+03:29:08.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 45 a2 17 00 00 00 25d+03:29:08.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 45 a2 16 00 00 00 25d+03:29:08.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 45 a2 15 00 00 00 25d+03:29:08.856 READ FPDMA QUEUED Error 290 [1] occurred at disk power-on lifetime: 41014 hours (1708 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 42 81 cb f8 00 00 24d+22:50:14.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 42 81 ca f8 00 00 24d+22:50:14.856 READ FPDMA QUEUED 60 00 20 00 08 00 00 17 a8 1c a8 00 01 24d+22:50:14.856 READ FPDMA QUEUED 60 00 80 00 00 00 00 17 a8 1c 28 00 00 24d+22:50:14.856 READ FPDMA QUEUED 60 00 40 00 00 00 00 17 a8 1b e8 00 00 24d+22:50:14.856 READ FPDMA QUEUED Error 289 [0] occurred at disk power-on lifetime: 41000 hours (1708 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 42 81 cb f8 00 00 24d+09:11:01.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 42 81 ca f8 00 00 24d+09:11:01.856 READ FPDMA QUEUED 61 00 08 00 00 00 00 37 c4 55 58 00 00 24d+09:11:01.856 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 00 00 24d+09:11:01.856 FLUSH CACHE EXT 61 03 f0 00 00 00 00 37 c4 51 68 00 00 24d+09:11:01.856 WRITE FPDMA QUEUED Error 288 [3] occurred at disk power-on lifetime: 40983 hours (1707 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 42 81 cb f8 00 00 23d+15:55:35.856 READ FPDMA QUEUED 60 01 00 00 00 00 00 42 81 ca f8 00 00 23d+15:55:35.856 READ FPDMA QUEUED 60 00 08 00 10 00 00 03 08 be c8 00 02 23d+15:55:35.856 READ FPDMA QUEUED 60 00 80 00 08 00 00 05 77 c4 80 00 01 23d+15:55:35.856 READ FPDMA QUEUED 60 00 80 00 00 00 00 05 77 5a 80 00 00 23d+15:55:35.856 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 48767 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 32/52 Celsius Lifetime Min/Max Temperature: 14/52 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 35 --- Lifetime Power-On Resets 0x01 0x010 4 52247 --- Power-on Hours 0x01 0x018 6 840297116362 --- Logical Sectors Written 0x01 0x020 6 6026601116 --- Number of Write Commands 0x01 0x028 6 2876471126464 --- Logical Sectors Read 0x01 0x030 6 21982753584 --- Number of Read Commands 0x01 0x038 6 1541000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 291 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 6 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 59 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: 57C52E4AFF8EDF967E3AAF399A06BB91 LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 30 9 Power_On_Hours -O--CK 089 089 000 - 52282 12 Power_Cycle_Count -O--CK 099 099 000 - 44 177 Wear_Leveling_Count PO--C- 088 088 005 - 846 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 30 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 3241 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 099 099 010 - 30 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 134 190 Airflow_Temperature_Cel -O--CK 060 048 000 - 40 194 Temperature_Celsius -O---K 060 048 000 - 40 (Min/Max 15/52) 195 ECC_Error_Rate -O-RC- 199 199 000 - 134 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 3 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 39 241 Total_LBAs_Written -O--CK 099 099 000 - 851969570722 242 Total_LBAs_Read -O--CK 098 098 000 - 2869004484876 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1810293223424 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 134 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 134 [1] occurred at disk power-on lifetime: 32463 hours (1352 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 11d+16:29:50.520 READ LOG EXT 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 11d+16:29:50.520 READ LOG EXT 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED Error 133 [0] occurred at disk power-on lifetime: 32463 hours (1352 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 11d+16:29:50.520 READ LOG EXT 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 60 00 08 00 00 00 00 67 1e 8a b0 00 00 11d+16:29:50.520 READ FPDMA QUEUED 60 00 08 00 00 00 00 67 1e 8a a8 00 00 11d+16:29:50.520 READ FPDMA QUEUED Error 132 [3] occurred at disk power-on lifetime: 32463 hours (1352 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 67 1e 8a b8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 60 00 08 00 00 00 00 67 1e 8a b0 00 00 11d+16:29:50.520 READ FPDMA QUEUED 60 00 08 00 00 00 00 67 1e 8a a8 00 00 11d+16:29:50.520 READ FPDMA QUEUED 60 00 08 00 00 00 00 67 1e 8a a0 00 00 11d+16:29:50.520 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 09 11d+16:29:50.520 READ LOG EXT Error 131 [2] occurred at disk power-on lifetime: 32463 hours (1352 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 48 00 00 58 64 2c b8 00 09 11d+16:29:50.520 READ FPDMA QUEUED 60 00 20 00 40 00 00 67 1f 4b 80 00 08 11d+16:29:50.520 READ FPDMA QUEUED 60 00 20 00 38 00 00 67 1f 43 40 00 07 11d+16:29:50.520 READ FPDMA QUEUED 60 00 20 00 30 00 00 67 1f 3f 80 00 06 11d+16:29:50.520 READ FPDMA QUEUED 60 00 20 00 28 00 00 67 1f 2e 60 00 05 11d+16:29:50.520 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 48802 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 32/52 Celsius Lifetime Min/Max Temperature: 15/52 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 44 --- Lifetime Power-On Resets 0x01 0x010 4 52282 --- Power-on Hours 0x01 0x018 6 851969570722 --- Logical Sectors Written 0x01 0x020 6 6146063070 --- Number of Write Commands 0x01 0x028 6 2869004484876 --- Logical Sectors Read 0x01 0x030 6 21582464613 --- Number of Read Commands 0x01 0x038 6 401000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 134 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 5 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 62 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 3 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: DF636CF92277C4895DD81A1DF2E1C972 LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 32 9 Power_On_Hours -O--CK 089 089 000 - 52279 12 Power_Cycle_Count -O--CK 099 099 000 - 42 177 Wear_Leveling_Count PO--C- 089 089 005 - 817 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 32 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 3274 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 099 099 010 - 32 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 059 046 000 - 41 194 Temperature_Celsius -O---K 059 046 000 - 41 (Min/Max 17/54) 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 241 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 37 241 Total_LBAs_Written -O--CK 099 099 000 - 828468788170 242 Total_LBAs_Read -O--CK 099 099 000 - 2630290166301 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1747796899840 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 33/54 Celsius Lifetime Min/Max Temperature: 17/54 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 42 --- Lifetime Power-On Resets 0x01 0x010 4 52279 --- Power-on Hours 0x01 0x018 6 828468788170 --- Logical Sectors Written 0x01 0x020 6 5939749289 --- Number of Write Commands 0x01 0x028 6 2630290166301 --- Logical Sectors Read 0x01 0x030 6 20593049459 --- Number of Read Commands 0x01 0x038 6 3227000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 79 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 361 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 241 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7LM960HMJP-00005 Serial Number: 2714F8DCAAD06AE231C909FEDDAF861B LU WWN Device Id: 5 002538 ... Firmware Version: GXT5204Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jun 11 13:15:23 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 098 098 010 - 46 9 Power_On_Hours -O--CK 089 089 000 - 52272 12 Power_Cycle_Count -O--CK 099 099 000 - 42 177 Wear_Leveling_Count PO--C- 088 088 005 - 822 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 46 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 098 098 010 - 3196 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 098 098 010 - 46 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 098 098 000 - 12279 190 Airflow_Temperature_Cel -O--CK 060 048 000 - 40 194 Temperature_Celsius -O---K 060 048 000 - 40 (Min/Max 17/52) 195 ECC_Error_Rate -O-RC- 001 001 000 - 12279 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 36 241 Total_LBAs_Written -O--CK 099 099 000 - 830197312308 242 Total_LBAs_Read -O--CK 099 099 000 - 2623430638644 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 1758785497088 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 12279 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12279 [2] occurred at disk power-on lifetime: 40760 hours (1698 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 00 00 00 02 e9 3f 00 00 00 35d+13:55:11.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3e 00 00 00 35d+13:55:11.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3d 00 00 00 35d+13:55:11.336 READ FPDMA QUEUED 60 01 00 00 08 00 00 02 e9 3c 00 00 01 35d+13:55:11.336 READ FPDMA QUEUED 60 00 20 00 00 00 00 00 e5 20 c0 00 00 35d+13:55:11.336 READ FPDMA QUEUED Error 12278 [1] occurred at disk power-on lifetime: 40759 hours (1698 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 00 00 00 02 e9 3f 00 00 00 35d+12:34:44.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3e 00 00 00 35d+12:34:44.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3d 00 00 00 35d+12:34:44.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3c 00 00 00 35d+12:34:44.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3b 00 00 00 35d+12:34:44.336 READ FPDMA QUEUED Error 12277 [0] occurred at disk power-on lifetime: 40748 hours (1697 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 00 00 00 02 e9 3f 00 00 00 35d+01:36:17.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3e 00 00 00 35d+01:36:17.336 READ FPDMA QUEUED 60 00 68 00 18 00 00 02 e9 3d 98 00 03 35d+01:36:17.336 READ FPDMA QUEUED 60 00 20 00 10 00 00 02 e9 3d 70 00 02 35d+01:36:17.336 READ FPDMA QUEUED 60 00 68 00 00 00 00 02 e9 3d 00 00 00 35d+01:36:17.336 READ FPDMA QUEUED Error 12276 [3] occurred at disk power-on lifetime: 40745 hours (1697 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 01 00 00 00 00 00 10 00 00 Error: at LBA = 0x00000010 = 16 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 00 00 00 02 e9 3f 00 00 00 34d+22:38:32.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3e 00 00 00 34d+22:38:32.336 READ FPDMA QUEUED 60 01 00 00 00 00 00 02 e9 3d 00 00 00 34d+22:38:32.336 READ FPDMA QUEUED 60 00 20 00 08 00 00 02 e9 3c e0 00 01 34d+22:38:32.336 READ FPDMA QUEUED 60 00 d8 00 00 00 00 02 e9 3c 00 00 00 34d+22:38:32.336 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 32/52 Celsius Lifetime Min/Max Temperature: 17/52 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 42 --- Lifetime Power-On Resets 0x01 0x010 4 52272 --- Power-on Hours 0x01 0x018 6 830197312308 --- Logical Sectors Written 0x01 0x020 6 5938512774 --- Number of Write Commands 0x01 0x028 6 2623430638644 --- Logical Sectors Read 0x01 0x030 6 20453827713 --- Number of Read Commands 0x01 0x038 6 766000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 12279 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 170 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 --- Current Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 390 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 11 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.20 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg0,hpsa_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_14 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_15 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-7-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address