/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000039668ca10b1 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:28 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 65 C Manufactured in week 28 of year 2015 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 52 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 240 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 3 3 3 9 6263068.537 0 write: 0 0 0 0 0 35888.100 0 verify: 0 0 0 0 0 764937.164 0 Non-medium error count: 46 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 3 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] # 3 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 18430 seconds [5.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 63920:51 [3835251 minutes] Number of background scans performed: 2666, scan progress: 44.05% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca10b2 attached SAS address = 0x5141877034ae2c02 attached phy identifier = 4 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca10b3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000039668ca10ad Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:29 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 65 C Manufactured in week 28 of year 2015 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 52 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 295 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 2 2 2 3 6282816.242 0 write: 0 24 24 24 127 39419.085 0 verify: 0 0 0 0 0 764952.503 0 Non-medium error count: 33 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 3 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] # 3 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 18430 seconds [5.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 63920:33 [3835233 minutes] Number of background scans performed: 2666, scan progress: 45.15% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 1 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: power on negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca10ae attached SAS address = 0x5141877034ae2c00 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 10 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 1 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca10af attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000039668ca1089 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:29 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 65 C Manufactured in week 28 of year 2015 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 53 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 298 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 22 22 22 22 6304871.906 0 write: 0 3 3 3 6 43047.178 0 verify: 0 1 1 1 1 764940.360 0 Non-medium error count: 39 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 3 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] # 3 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 18430 seconds [5.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 63920:35 [3835235 minutes] Number of background scans performed: 2666, scan progress: 45.09% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca108a attached SAS address = 0x5141877034ae2c06 attached phy identifier = 6 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 4 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca108b attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000039668ca13f9 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:30 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 65 C Manufactured in week 28 of year 2015 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 53 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 266 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 4 4 4 6 6288801.722 0 write: 0 0 0 0 0 40778.930 0 verify: 0 0 0 0 0 764933.706 0 Non-medium error count: 55 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 3 - [- - -] # 2 Reserved(7) Completed 64 3 - [- - -] # 3 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 18430 seconds [5.1 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 63921:17 [3835277 minutes] Number of background scans performed: 2666, scan progress: 45.11% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca13fa attached SAS address = 0x5141877034ae2c05 attached phy identifier = 2 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000039668ca13fb attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG02 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x500003975833bd34 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:30 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 50 C Manufactured in week 42 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 39 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 1334 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 467 507 467 10660 3497810.051 40 write: 0 12 83 12 5799 197876.296 71 verify: 0 45 54 45 774 420906.913 9 Non-medium error count: 36 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36490:27 [2189427 minutes] Number of background scans performed: 961, scan progress: 44.10% Number of background medium scans performed: 0 # when lba(hex) [sk,asc,ascq] reassign_status 1 34079:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 2 34103:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 3 34127:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 4 34151:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 5 34175:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 6 34199:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 7 34223:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 8 34247:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 9 34271:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 10 34295:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 11 34319:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 12 34343:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 13 34367:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 14 34391:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 15 34415:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 16 34439:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 17 34463:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 18 34487:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 19 34511:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 20 34535:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 21 34559:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 22 34583:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 23 34607:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 24 34631:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 25 34655:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 26 34679:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 27 34703:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 28 34724:45 000000000491f067 [3,11,1] Reassigned by app, has valid data 29 34748:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 30 34772:22 000000000491f067 [3,11,1] Reassigned by app, has valid data 31 34796:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 32 34820:22 000000000491f067 [3,11,1] Reassigned by app, has valid data 33 34845:19 000000000491f067 [3,11,1] Reassigned by app, has valid data 34 34868:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 35 34892:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 36 34916:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 37 34940:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 38 34964:25 000000000491f067 [3,11,1] Reassigned by app, has valid data 39 34988:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 40 35012:58 000000000491f067 [3,11,1] Reassigned by app, has valid data 41 35036:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 42 35060:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 43 35084:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 44 35108:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 45 35132:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 46 35156:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 47 35181:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 48 35204:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 49 35228:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 50 35252:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 51 35276:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 52 35300:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 53 35324:21 000000000491f067 [3,11,1] Reassigned by app, has valid data 54 35349:12 000000000491f067 [3,11,1] Reassigned by app, has valid data 55 35372:22 000000000491f067 [3,11,1] Reassigned by app, has valid data 56 35396:22 000000000491f067 [3,11,1] Reassigned by app, has valid data 57 35420:23 000000000491f067 [3,11,1] Reassigned by app, has valid data 58 35444:23 000000000491f067 [3,11,1] Reassigned by app, has valid data 59 35468:23 000000000491f067 [3,11,1] Reassigned by app, has valid data 60 35492:23 000000000491f067 [3,11,1] Reassigned by app, has valid data 61 35516:48 000000000491f067 [3,11,1] Reassigned by app, has valid data 62 35540:23 000000000491f067 [3,11,1] Reassigned by app, has valid data 63 35566:32 000000000491f067 [3,11,1] Reassigned by app, has valid data 64 36072:01 000000000491f067 [3,11,1] Reassigned by app, has valid data 65 36095:54 000000000491f067 [3,11,1] Reassigned by app, has valid data 66 36120:01 000000000491f067 [3,11,1] Reassigned by app, has valid data 67 36144:06 000000000491f067 [3,11,1] Reassigned by app, has valid data 68 36169:14 000000000491f067 [3,11,1] Reassigned by app, has valid data 69 36203:42 000000000491f067 [3,11,1] Reassigned by app, has valid data 70 36230:40 000000000491f067 [3,11,1] Reassigned by app, has valid data Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500003975833bd36 attached SAS address = 0x5141877034ae2c03 attached phy identifier = 5 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 2 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500003975833bd37 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG02 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x500003975833bd24 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:30 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 50 C Manufactured in week 42 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 39 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 1359 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 535 535 535 538 3599458.653 0 write: 0 1 1 1 1 196523.799 0 verify: 0 84 84 84 84 420999.945 0 Non-medium error count: 40 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36515:45 [2190945 minutes] Number of background scans performed: 1021, scan progress: 38.12% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: loss of dword synchronization reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500003975833bd26 attached SAS address = 0x5141877034ae2c07 attached phy identifier = 1 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 37 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500003975833bd27 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x50000397282bb035 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:31 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 65 C Manufactured in week 29 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 44 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 16429 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 133 133 133 155 4640005.204 0 write: 0 0 0 0 0 42679.449 0 verify: 0 18 18 18 18 503660.592 0 Non-medium error count: 28 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 43081:50 [2584910 minutes] Number of background scans performed: 1581, scan progress: 40.70% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x50000397282bb036 attached SAS address = 0x5141877034ae2c04 attached phy identifier = 7 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x50000397282bb037 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 /dev/sda,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.3.12-200.fc38.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: TOSHIBA Product: MG03SCA200 Revision: DG09 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x50000396c8098c45 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Jul 17 19:11:31 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 30 C Drive Trip Temperature: 65 C Manufactured in week 01 of year 2016 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 49 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 16108 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 355 355 355 364 5023559.786 0 write: 0 0 0 0 0 52174.277 0 verify: 0 50 50 50 50 551671.302 0 Non-medium error count: 35 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 47266:52 [2836012 minutes] Number of background scans performed: 1699, scan progress: 38.24% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 2 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x50000396c8098c46 attached SAS address = 0x5141877034ae2c01 attached phy identifier = 3 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0 relative target port id = 2 generation code = 2 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x50000396c8098c47 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 Phy event descriptors: Elasticity buffer overflow count: 0 Received abandon-class OPEN_REJECT count: 0 Transmitted BREAK count: 0 Received BREAK count: 0 Transmitted SSP frame error count: 0 Received SSP frame error count: 0